- 您现在的位置：买卖IC网 > PDF目录80355 > M37641F8HP 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M37641F8HP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 12 X 12 MM, 0.50 MM PITCH, PLASTIC, LQFP-80 |
| 文件页数： | 37/136页 |
| 文件大小： | 1672K |
| 代理商： | M37641F8HP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
131
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Frequency Synthesizer
The frequency synthesizer and DC-DC converter must be set up
as follows when recovering from a Hardware Reset:
(1) Enable the frequency synthesizer after setting the frequency
synthesizer related registers (addresses 006C16 to 006F16).
Then wait for 2 ms.
(2) Check the Frequency Synthesizer Lock Status Bit. If “0”, wait
for 0.1 ms and then recheck.
(3) When using the USB built-in DC-DC converter, set the USB
Line Driver Supply Enable Bit of the USB control register to
“1”. This setting must be done 2 ms or more after the setup
described in step (1). The USB Line Driver Current Control Bit
must be set to “0” at this time. (When Vcc = 3.3V, the setting
explained in this step is not necessary.)
(4) After waiting for (C + 1) ms so that the external capacitance
pin (Ext. Cap. pin) can reach approximately 3.3 V, set the
USB Clock Enable Bit to “1”. At this time, “C” equals the ca-
pacitance (
F) of the capacitor connected to the Ext. Cap.
pin. For example, if 2.2
F and 0.1 F capacitors are con-
nected to the Ext. Cap. in parallel, the required wait will be
(2.3 + 1) ms.
(5) After enabling the USB clock, wait for 4 or more
φ cycles, and
then set the USB Enable Bit to “1”.
Bits 6 and 5 of the frequency synthesizer control register (ad-
dress 006C16) are initialized to “11” after reset release. Make
sure to set bits 6 and 5 to “10” after the Frequency Synthesizer
Lock Status Bit goes to “1”.
When using the frequency synthesized clock function, we recom-
mend using the fastest frequency possible of f(XIN) or f(XCIN) as
an input clock for the PLL. Owing to the PLL mechanism, the PLL
controls the speed of multiplied clocks from the source clock. As
a result, when the source clock input is lower, the generated clock
becomes less stable. This is because more multipliers are
needed and the speed control is very rough. Higher source clock
input generates a stabler clock, as less multipliers are needed
and the speed control is more accurate. However, if the input
clock frequency is relatively high, the PLL clock generator can
quickly lock-up the output clock to the source and make the out-
put clock very stable.
Set the value of frequency synthesizer multiply register 2 (FSM2)
so that the fPIN is 1 MHZ or higher.
DMA
In the memory expansion mode and microprocessor mode, the
DMAOUT pin outputs “H” during a DMA transfer.
Do not access the DMAC-related registers by using a DMAC
transfer. The destination address data and the source address
data will collide in the DMAC internal bus.
When using the USB FIFO as the DMA transfer source, make
sure that, if you use the AUTO_SET function, short packet data
does not get mixed in with the transfer data.
When setting the DMAC channel x enable bit (bit 7 of address
004116) to “1”, be sure simultaneously to set the DMAC channel x
transfer initiation source capture register reset bit (bit 6 of ad-
dress 004116) to “1”. If this is not performed, an incorrect data will
be transferred at the same time when the DMAC is enabled.
Memory Expansion Mode & Microprocessor
Mode
In both memory expansion mode and microprocessor mode, use
the LDM instruction or STA instruction to write to port P3 (address
000E16). When using the Read-Modify-Write instruction (SEB in-
struction, CLB instruction) you will need to map a memory that
the CPU can read from and write to.
In the memory expansion mode, if the internal and external
memory areas overlap, the internal memory becomes the valid
memory for the overlapping area. When the CPU performs a read
or a write operation on this overlapped area, the following things
happen:
(1) Read
The CPU reads out the data in the internal memory instead of
in the external memory. Note that, since the CPU will output a
proper read signal, address signal, etc., the memory data at
the respective address will appear on the external data bus.
(2) Write
The CPU writes data to both the internal and external memo-
ries.
The wait function is serviceable at accessing an external memory.
Stop Mode
When the STP instruction is executed, bit 7 of the clock control
register (address 001F16) goes to “0”. To return from stop mode,
reset CCR7 to “1”.
When using fSYN (set Internal System Clock Select Bit (CPMA6)
to “1”) as the internal system clock, switch CPMA6 to “0” before
executing the STP instruction. Reset CPMA6 after the system re-
turns from Stop Mode and the frequency synthesizer has
stabilized.
CPMA6 does not need to be switched to “0” when using the WIT
instruction.
When the STP instruction is being executed, all bits except bit 4
of the timer 123 mode register (address 002916) are initialized to
“0”. It is not necessary to set T123M1 (Timer 1 Count Stop Bit) to
“0” before executing the STP instruction. After returning from Stop
Mode, reset the timer 1 (address 002416), timer 2 (address
002516), and the timer 123 mode register (address 002916).
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711N4CFS2 | 8-BIT, UVPROM, 2 MHz, MICROCONTROLLER, CQCC84 |
| MC68HC11KS2VPU2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC711KS2MFN2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PQCC68 |
| MB89163-PFM | 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC08JB8JDW | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37641F8HP#U0 | 功能描述:IC 740 MCU FLASH 32K 80LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/7600 产品培训模块:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 标准包装:27 系列:PIC® 24H 核心处理器:PIC 芯体尺寸:16-位 速度:40 MIP 连通性:I²C，SPI，UART/USART 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:21 程序存储器容量:12KB（4K x 24） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 3.6 V 数据转换器:A/D 10x10b/12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 包装:管件 产品目录页面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2 |
| M37641F8M8-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8-XXXHP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。