- 您现在的位置：买卖IC网 > PDF目录80355 > M37641F8HP 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M37641F8HP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 12 X 12 MM, 0.50 MM PITCH, PLASTIC, LQFP-80 |
| 文件页数： | 86/136页 |
| 文件大小： | 1672K |
| 代理商： | M37641F8HP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页当前第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
53
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
[USB Endpoint 0 IN Control Register ] IN_CSR
This register contains the control and status information of the
endpoint 0. This USB FCU sets the OUT_PKT_RDY flag to “1”
upon having received a data packet in the OUT FIFO. When read-
ing its one data packet from the OUT FIFO, be sure to set this flag
to “0”.
After a SETUP token is received, the MCU is in the “decode wait
state ” until the OUT_PKT_RDY flag is cleared. If the
OUT_PKT_RDY flag is not cleared (indicating that the host re-
quest has not been successfully decoded), the USB FCU keep
returning a NAK to the host for all IN/OUT tokens.
Set the IN_PKT_RDY bit to “1” after the data packet has been
written to the IN FIFO. If this bit is set to “1” even though nothing
has been written to the IN FIFO, a “0” length data (NULL packet)
is sent to the host. The SEND_STALL bit is for sending a STALL to
the host if an unsupported request is received by the USB FCU.
This bit must be set to “1”. When the OUT_PKT_RDY flag is set to
“0” for request reception, the USB FCU transmits a STALL signal
to the Host CPU. Perform the following three processes simulta-
neously:
Set SEND_STALL bit to “1”
Set DATA_END bit to “1”
Set OUT_PKT_RDY flag to “0” by setting SERVICED_OUT
_PKT_RDY bit to “1”.
Note that if “0” is written to the SEND_STALL bit before the
CLEAR_FEATURE (endpoint STALL) request has been received,
the next STALL will not be generated.
The DATA_END bit informs the USB FCU of the completion of the
process indicated in the SETUP packet. Set this bit to “1” when
the process requested in the SETUP packet is completed. (Con-
trol Read Transfer: set this bit after writing all of the requested
data to the FIFO; Control Write Transfer: set this bit to “1” after
reading all of the requested data from the FIFO.) When this bit is
“1”, the host request is ignored and a STALL is returned. After the
status phase process is completed, the USB FCU automatically
clears it to “0”.
USB endpoint 0 IN control register (address 005916)
IN_CSR
OUT_PKT_RDY flag (IN0CSR0)
0: Except the following condition (Cleared to “0” by writing “1” into
SERVICED_OUT_PKT_RDY bit)
1: End of a data packet reception
IN_PKT_RDY bit (IN0CSR1)
0: End of a data packet transmission
1: Write “1” at completion of writing a data packet into IN FIFO.
SEND_STALL bit (IN0CSR2)
0: Except the following condition
1: Transmitting STALL handshake signal
DATA_END bit (IN0CSR3)
0: Except the following condition (Cleared to “0” after completion of
status phase)
1: Write “1” at completion of writing or reading the last data packet
to/from FIFO.
FORCE_STALL flag (IN0CSR4)
0: Except the following condition
1: Protocol error detected
SETUP_END flag (IN0CSR5) (Note )
0: Except the following condition (Cleared to “0” by writing “1” into
SERVICED_SETUP_END bit)
1: Control transfer ends before the specific length of data is
transferred during the data phase.
SERVICED_OUT_PKT_RDY bit (IN0CSR6)
Writing “1” to this bit clears OUT_PKT_RDY flag to “0”.
SERVICED_SETUP_END bit (IN0CSR7)
Writing “1” to this bit clears SETUP_END flag to “0”.
b0
b7
Note: If this bit is set to “0”, stop accessing the FIFO to serve the previous setup transaction.
Fig. 46 Structure of USB endpoint 0 IN control register
By making the O bit to be "1", the flag is made to be "0".
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711N4CFS2 | 8-BIT, UVPROM, 2 MHz, MICROCONTROLLER, CQCC84 |
| MC68HC11KS2VPU2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC711KS2MFN2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PQCC68 |
| MB89163-PFM | 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC08JB8JDW | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37641F8HP#U0 | 功能描述:IC 740 MCU FLASH 32K 80LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/7600 产品培训模块:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 标准包装:27 系列:PIC® 24H 核心处理器:PIC 芯体尺寸:16-位 速度:40 MIP 连通性:I²C，SPI，UART/USART 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:21 程序存储器容量:12KB（4K x 24） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 3.6 V 数据转换器:A/D 10x10b/12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 包装:管件 产品目录页面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2 |
| M37641F8M8-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8-XXXHP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。