参数资料
型号: M38027M8DXXXFP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
封装: 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-64
文件页数: 11/54页
文件大小: 590K
代理商: M38027M8DXXXFP
MITSUBISHI MICROCOMPUTERS
3802 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
16
Timer X count stop bit
0: Count start
1: Count stop
Timer XY mode register
(TM : address 002316)
Timer Y operating mode bit
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
CNTR1 active edge switch bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
b7
CNTR0 active edge switch bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
b0
Timer X operating mode bit
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
b1b0
b4b5
Timer Y count stop bit
0: Count start
1: Count stop
Timers
The 3802 group has four timers: timer X, timer Y, timer 1, and timer
2.
All timers are count down. When the timer reaches “0016”, an un-
derflow occurs at the next count pulse and the corresponding
timer latch is reloaded into the timer and the count is continued.
When a timer underflows, the interrupt request bit corresponding
to that timer is set to “1”.
The division ratio of each timer or prescaler is given by 1/(n + 1),
where n is the value in the corresponding timer or prescaler latch.
Timer 1 and Timer 2
The count source of prescaler 12 is the oscillation frequency di-
vided by 16. The output of prescaler 12 is counted by timer 1 and
timer 2, and a timer underflow sets the interrupt request bit.
Timer X and Timer Y
Timer X and Timer Y can each be selected in one of four operating
modes by setting the timer XY mode register.
Timer Mode
The timer counts f(XIN)/16 in timer mode.
Pulse Output Mode
Timer X (or timer Y) counts f(XIN)/16. Whenever the contents of
the timer reach “0016”, the signal output from the CNTR0 (or
CNTR1) pin is inverted. If the CNTR0 (or CNTR1) active edge
switch bit is “0”, output begins at “ H”.
If it is “1”, output starts at “L”. When using a timer in this mode, set
the corresponding port P54 ( or port P55) direction register to out-
put mode.
Event Counter Mode
Operation in event counter mode is the same as in timer mode,
except the timer counts signals input through the CNTR0 or
CNTR1 pin.
Pulse Width Measurement Mode
If the CNTR0 (or CNTR1) active edge selection bit is “0”, the timer
counts at the oscillation frequency divided by 16 while the CNTR0
(or CNTR1) pin is at “H”. If the CNTR0 (or CNTR1) active edge
switch bit is “1”, the count continues during the time that the
CNTR0 (or CNTR1) pin is at “L”.
In all of these modes, the count can be stopped by setting the
timer X (timer Y) count stop bit to “1”. Every time a timer
underflows, the corresponding interrupt request bit is set.
Fig. 8 Structure of timer XY register
相关PDF资料
PDF描述
MB90549GPMC 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
MB90347CESPMC 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100
MB90348ESPMC 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100
MB90F343ESPMC 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
MB90F423GCPMC 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100
相关代理商/技术参数
参数描述
M3802-BLACK-100 制造商:Alpha Wire 功能描述:
M3803 BK005 制造商:Alpha Wire 功能描述:CBL 5COND 18AWG BLK 100'
M38037M5H-175HP#U0 制造商:Renesas Electronics Corporation 功能描述:8BIT CISC - Trays
M38037M8108F 制造商:Panasonic Industrial Company 功能描述:IC
M38037M8H-194HP#U0 制造商:Renesas Electronics Corporation 功能描述:8BIT CISC - Trays