- 您现在的位置：买卖IC网 > PDF目录102740 > M41T93RMY6E (STMICROELECTRONICS) 1 TIMER(S), REAL TIME CLOCK, PDSO18 PDF资料下载
参数资料
| 型号： | M41T93RMY6E |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO18 |
| 封装： | 0.300 INCH, ROHS COMPLIANT, PLASTIC, SOP-18 |
| 文件页数： | 13/49页 |
| 文件大小： | 719K |
| 代理商： | M41T93RMY6E |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Clock operation
M41T93
Doc ID 12615 Rev 5
3.4
Clock calibration
The M41T93 oscillator is designed for use with a 12.5 pF crystal load capacitance. When
the calibration circuit is properly employed, accuracy improves to better than ±1 ppm at
25 °C.
The M41T93 design provides the following two methods for clock error correction.
3.4.1
Digital calibration (periodic counter correction)
This method employs the use of periodic counter correction by adjusting the ratio of the
100 Hz divider stage to the 512 Hz divider stage. Under normal operation, the 100Hz divider
stage outputs precisely 100 pulses for every 512 pulses of the 512 Hz input stage to provide
the input frequency to the fraction of seconds clock register. By adjusting the number of
512 Hz input pulses used to generate 100 output pulses, the clock can be sped up or slowed
down, as shown in Figure 12 on page 25.
When a non-zero value is loaded into the five calibration bits (DC4 – DC0) found in the
digital calibration register (08h) and the sign bit is ‘1,’ (indicating positive calibration), the
100 Hz stage outputs 100 pulses for every 511 input pulses instead of the normal 512.
Since the 100 pulses are now being output in a shorter window, this has the effect of
speeding up the clock by 1/512 seconds for each second the circuit is active. Similarly, when
the sign bit is ‘0,’ indicating negative calibration, the block outputs 100 pulses for every 513
input pulses. Since the 100 pulses are then being output in a longer window, this has the
effect of slowing down the clock by 1/512 seconds for each second the circuit is active.
The amount of calibration is controlled by using the value in the calibration register (N) to
generate the adjustment in one second increments. This is done for the first N seconds once
every eight minutes for positive calibration, and for N seconds once every sixteen minutes
for negative calibration (see Table 4 on page 21).
For example, if the calibration register is set to '100010,' then the adjustment will occur for
two seconds in every minute. Similarly, if the calibration register is set to '000011,' then the
adjustment will occur for 3 seconds in every alternating minute.
The digital calibration bits (DC4 – DC0) occupy the five lower order bits in the digital
calibration register (08h). These bits can be set to represent any value between 0 and 31 in
binary form. The sixth bit (DCS) is a sign bit; '1' indicates positive calibration, '0' indicates
negative calibration. Calibration occurs within an 8-minute (positive) or 16-minute (negative)
cycle. Therefore, each calibration step has an effect on clock accuracy of +4.068 or –2.034
ppm. Assuming that the oscillator is running at exactly 32,768 Hz, each of the 31 increments
in the calibration byte would represent +10.7 or –5.35 seconds per month, which
corresponds to a total range of +5.5 or –2.75 minutes per month.
Note:
1
The modified pulses are not observable on the frequency test (FT) output, nor will the effect
of the calibration be measurable real-time, due to the periodic nature of the error
compensation.
2
Positive digital calibration is performed on an eight minute cycle, therefore the value in the
calibration register should not be modified more frequently than once every eight minutes for
positive values of calibration. Negative digital calibration is performed on a sixteen minute
cycle, therefore negative values in the calibration register should not be modified more
frequently than once every sixteen minutes.
相关PDF资料 |
PDF描述 |
|---|---|
| MN101CA5F | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP112 |
| MC68HC908QY8MDTE | 8-BIT, FLASH, 32 MHz, MICROCONTROLLER, PDSO16 |
| MC9S12C64MFAE25 | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP48 |
| MC312XDP512F0VAG | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP144 |
| MC912XDP512F0CAA | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M41T93RMY6F | 功能描述:实时时钟 Serial SPI bus RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M41T93RMY6F-CUT TAPE | 制造商:ST 功能描述:M41T93 Series 5.5 V Serial SPI Bus RTC with Battery Switchover - SOX-18 |
| M41T93RQA6E | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Serial SPI bus RTC with battery switchover |
| M41T93RQA6F | 功能描述:实时时钟 SPI RTC 32.768 kHz 365nA 2.0V to 5.5V RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M41T93RQA6F-CUT TAPE | 制造商:ST 功能描述:M41T93 Series 5.5 V Serial SPI Bus RTC With Battery Switchover -QFN-16 |
发布紧急采购，3分钟左右您将得到回复。