- 您现在的位置：买卖IC网 > PDF目录229296 > M93C76-WDS6G (STMICROELECTRONICS) 512 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | M93C76-WDS6G |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | PROM |
| 英文描述： | 512 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 封装： | 3 X 3 MM, ROHS COMPLIANT, TSSOP-8 |
| 文件页数： | 2/38页 |
| 文件大小： | 348K |
| 代理商： | M93C76-WDS6G |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
Operating features
M93C86, M93C76, M93C66, M93C56, M93C46
3
Operating features
3.1
Supply voltage (VCC)
3.1.1
Operating supply voltage VCC
Prior to selecting the memory and issuing instructions to it, a valid and stable VCC voltage
within the specified [VCC(min), VCC(max)] range must be applied. In order to secure a stable
DC supply voltage, it is recommended to decouple the VCC line with a suitable capacitor
(usually of the order of 10 nF to 100 nF) close to the VCC/VSS package pins.
This voltage must remain stable and valid until the end of the transmission of the instruction
and, for a Write instruction, until the completion of the internal write cycle (tW).
3.1.2
Power-up conditions
When the power supply is turned on, VCC rises from VSS to VCC. During this time, the Chip
Select (S) line is not allowed to float and should be driven to VSS, it is therefore
recommended to connect the S line to VCC via a suitable pull-down resistor.
The VCC rise time must not vary faster than 1 V/s.
3.1.3
Power-up and device reset
In order to prevent inadvertent Write operations during power-up, a power on reset (POR)
circuit is included. At power-up (continuous rise of VCC), the device does not respond to any
instruction until VCC has reached the power on reset threshold voltage (this threshold is
When VCC passes the POR threshold, the device is reset and is in the following state:
●
Standby Power mode
●
deselected (assuming that there is a pull-down resistor on the S line)
3.1.4
Power-down
At power-down (continuous decrease in VCC), as soon as VCC drops from the normal
operating voltage to below the power on reset threshold voltage, the device stops
responding to any instruction sent to it.
During power-down, the device must be deselected and in the Standby Power mode (that is,
there should be no internal Write cycle in progress).
相关PDF资料 |
PDF描述 |
|---|---|
| ML1I-65656V-100SHXXX | 32K X 8 STANDARD SRAM, 100 ns, CDIP28 |
| MLCP-65656V-100/883 | 32K X 8 STANDARD SRAM, 100 ns, CDIP28 |
| ML1I-65656L-80/883:D | 32K X 8 STANDARD SRAM, 80 ns, CDIP28 |
| MLCP-65656L-85 | 32K X 8 STANDARD SRAM, 85 ns, CDIP28 |
| MM1K-67132V-35:D | 2K X 8 DUAL-PORT SRAM, 35 ns, CDIP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M93C-76WDS7P | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM |
| M93C76-WMN3TP/S | 制造商:STMicroelectronics 功能描述:EEPROM Serial-Microwire 8K-bit 1K x 8/512 x 16 3.3V/5V 8-Pin SO N T/R |
| M93C76-WMN6 | 功能描述:电可擦除可编程只读存储器 8K (1Kx8 or 512x16) RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| M93C-76WMN6P | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or 16-bit wide) MICROWIRE Serial Access EEPROM |
| M93C76-WMN6P | 功能描述:电可擦除可编程只读存储器 16 Kbit 8 Kbit 4Kbit 2 Kbit and 1 Kbit RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。