- 您现在的位置：买卖IC网 > PDF目录180438 > M95320-BN6 (STMICROELECTRONICS) 4K X 8 SPI BUS SERIAL EEPROM, PDIP8 PDF资料下载
参数资料
| 型号： | M95320-BN6 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | PROM |
| 英文描述： | 4K X 8 SPI BUS SERIAL EEPROM, PDIP8 |
| 封装： | PLASTIC, DIP-8 |
| 文件页数： | 39/42页 |
| 文件大小： | 771K |
| 代理商： | M95320-BN6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页
M95640, M95320
6/42
SIGNAL DESCRIPTION
During all operations, VCC must be held stable and
within the specified valid range: VCC(min) to
VCC(max).
All of the input and output signals must be held
High or Low (according to voltages of VIH, VOH, VIL
These signals are described next.
Serial Data Output (Q). This output signal is
used to transfer data serially out of the device.
Data is shifted out on the falling edge of Serial
Clock (C).
Serial Data Input (D). This input signal is used to
transfer data serially into the device. It receives in-
structions, addresses, and the data to be written.
Values are latched on the rising edge of Serial
Clock (C).
Serial Clock (C). This input signal provides the
timing of the serial interface. Instructions, address-
es, or data present at Serial Data Input (D) are
latched on the rising edge of Serial Clock (C). Data
on Serial Data Output (Q) changes after the falling
edge of Serial Clock (C).
Chip Select (S). When this input signal is High,
the device is deselected and Serial Data Output
(Q) is at high impedance. Unless an internal Write
cycle is in progress, the device will be in the Stand-
by Power mode. Driving Chip Select (S) Low se-
lects the device, placing it in the Active Power
mode.
After Power-up, a falling edge on Chip Select (S)
is required prior to the start of any instruction.
Hold (HOLD). The Hold (HOLD) signal is used to
pause any serial communications with the device
without deselecting the device.
During the Hold condition, the Serial Data Output
(Q) is high impedance, and Serial Data Input (D)
and Serial Clock (C) are Don’t Care.
To start the Hold condition, the device must be se-
lected, with Chip Select (S) driven Low.
Write Protect (W). The main purpose of this in-
put signal is to freeze the size of the area of mem-
ory that is protected against Write instructions (as
specified by the values in the BP1 and BP0 bits of
the Status Register).
This pin must be driven either High or Low, and
must be stable during all write operations.
相关PDF资料 |
PDF描述 |
|---|---|
| M95P-15-30-135 | PCB CONNECTOR, PLUG |
| M95S-15-30-135 | PCB CONNECTOR, SOCKET |
| MA-121-060-235-0200 | 60 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER, RECEPTACLE |
| MA-121-060-235-02WN | 60 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER, RECEPTACLE |
| MA-121-060-235-0500 | 60 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER, RECEPTACLE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M95320-BN6G | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:32Kbit and 64Kbit Serial SPI Bus EEPROMs With High Speed Clock |
| M95320-BN6P | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:32Kbit and 64Kbit Serial SPI Bus EEPROMs With High Speed Clock |
| M95320-BN6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:32Kbit and 64Kbit Serial SPI Bus EEPROMs With High Speed Clock |
| M95320-BN6TG | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:32Kbit and 64Kbit Serial SPI Bus EEPROMs With High Speed Clock |
| M95320-BN6TP | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:32Kbit and 64Kbit Serial SPI Bus EEPROMs With High Speed Clock |
发布紧急采购，3分钟左右您将得到回复。