参数资料
型号: M95320-WDW6TG
厂商: NUMONYX
元件分类: PROM
英文描述: 4K X 8 FLASH 2.7V PROM, PDSO8
封装: 0.169 INCH, ROHS COMPLIANT, TSSOP-8
文件页数: 5/45页
文件大小: 440K
代理商: M95320-WDW6TG
M95320, M95640, M95320-x, M95640-x
Operating features
4.3
Status Register
Figure 6 shows the position of the Status Register in the control logic of the device. The
Status Register contains a number of status and control bits that can be read or set (as
appropriate) by specific instructions. See Section 6.3: Read Status Register (RDSR) for a
detailed description of the Status Register bits.
4.4
Data protection and protocol control
Non-volatile memory devices can be used in environments that are particularly noisy, and
within applications that could experience problems if memory bytes are corrupted.
Consequently, the device features the following data protection mechanisms:
Write and Write Status Register instructions are checked that they consist of a number
of clock pulses that is a multiple of eight, before they are accepted for execution.
All instructions that modify data must be preceded by a Write Enable (WREN)
instruction to set the Write Enable Latch (WEL) bit. This bit is returned to its reset state
by the following events:
–Power-up
Write Disable (WRDI) instruction completion
Write Status Register (WRSR) instruction completion
Write (WRITE) instruction completion
The Block Protect (BP1, BP0) bits allow part of the memory to be configured as read-
only. This is the Software Protected Mode (SPM).
The Write Protect (W) signal allows the Block Protect (BP1, BP0) bits to be protected.
This is the Hardware Protected Mode (HPM).
For any instruction to be accepted, and executed, Chip Select (S) must be driven High after
the rising edge of Serial Clock (C) for the last bit of the instruction, and before the next rising
edge of Serial Clock (C).
Two points need to be noted in the previous sentence:
The ‘last bit of the instruction’ can be the eighth bit of the instruction code, or the eighth
bit of a data byte, depending on the instruction (except for Read Status Register
(RDSR) and Read (READ) instructions).
The ‘next rising edge of Serial Clock (C)’ might (or might not) be the next bus
transaction for some other device on the SPI bus.
Table 2.
Write-Protected block size
Status Register Bits
Protected Block
Array Addresses Protected
BP1
BP0
M95640, M95640-W,
M95640-R, M95640-S
M95320, M95320-W,
M95320-R, M95320-S
0
none
0
1
Upper quarter
1800h - 1FFFh
0C00h - 0FFFh
1
0
Upper half
1000h - 1FFFh
0800h - 0FFFh
1
Whole memory
0000h - 1FFFh
0000h - 0FFFh
相关PDF资料
PDF描述
MA-191 MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, CRIMP; SOLDER, PLUG
MA-1A1 FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, CRIMP; SOLDER, RECEPTACLE
MA142ATX 0.1 A, SILICON, SIGNAL DIODE
MA206 0.1 A, 2 ELEMENT, SILICON, SIGNAL DIODE
MA27P010G SILICON, PIN DIODE
相关代理商/技术参数
参数描述
M95320-WDW6TG/P 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:32 Kbit serial SPI bus EEPROMs with high-speed clock
M95320-WDW6TG/PC 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:32 Kbit serial SPI bus EEPROMs with high-speed clock
M95320WDW6TP 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:32 Kbit and 64 Kbit serial SPI bus EEPROMs with high-speed clock
M95320-WDW6TP 功能描述:电可擦除可编程只读存储器 2.5 V to 5.5V 32k RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
M95320-WDW6TP/P 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:32 Kbit serial SPI bus EEPROMs with high-speed clock