- 您现在的位置：买卖IC网 > PDF目录383307 > MA3691 (Dynex Semiconductor Ltd.) 1553B Bus Controller/Remote Terminal PDF资料下载
参数资料
| 型号： | MA3691 |
| 厂商： | Dynex Semiconductor Ltd. |
| 英文描述： | 1553B Bus Controller/Remote Terminal |
| 中文描述： | 1553B总线控制器/远程终端 |
| 文件页数： | 4/41页 |
| 文件大小： | 426K |
| 代理商： | MA3691 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
MA3690/1/3
4/41
OPERATION IN BUS CONTROL MODE
For this mode of operation the RT/BC pin must be held in
the logic zero state. On power up the PUC or RESET line must
be pulsed low for a minimum of 500ns causing the chip set to
initialise and assume the halted state with the HALTED output
low. To release the terminal from the halted state, the
subsystem must drive the HALTREQ line through a low to high
transition, at which time the HALTED line will go inactive.
When the HALTED line goes inactive,the terminal will
address a four word deep Instruction Store as shown below,
using the C0 and Cl outputs.
This first instruction after a Reset is a NOOP.
INSTRUCTION STORE
C1
C0
Word
0
0
1
1
0
1
0
1
Instruction
Receive Command
Transmit Command
Data Pointer
The instruction word specifies the operation which the
terminal is to carry out, and is formatted in the following way:
Instruction Word
Bit
15.14. 13.12.11. 10.9.8.7.
Retry
Retry
Count Condition Conditlon Select Code
6.5.
Bus
4.3.
Functlon Message
2.1.0.
Interrupt
Code
The significance of the instruction word bits are as follows:
Message Code
Code
Transfer Type
000
001
010
011
100
101
110
111
RT to BC
BC to RT
RT to RT, data to BC subsystem
RT to RT, no data to BC subsystem
Broadcast RT to BC, non data mode commands only
Broadcast BC to RT
Broadcast RT to RT, data to BC subsystem
Broadcast RT to RT, no data to BC subsystem
Mode Codes without data are followed by a NOOP.
Function Code
Code
Terminal Function
00
01
10
11
Execute message code
Perform self test
Monitor bus
No operation (NOOP)
The Function Code (bits 4 and 3 of the Instruction Word)
specifies the required terminal mode of operation.
Execute - Code 00
With the Function code bits set to 00, the terminal will
execute the message as defined in the Message code bits
Self Test - Code 01
If the terminal has been selected to perform a Self Test
then the terminal transmitter output stages will be disabled and
the self test sequence entered. At the end of the Self Test the
transmitter stages will be re-enabled and a Report sequence
will be activated, in order to report on the success, or failure, of
the Self Test.
Passive Monitor - Code 10
If the Function code of the Instruction word is 10 the
terminal will disable the transmitter output stages, suspend
table execution and merely monitor the specified bus for valid
words.
No Operation - Code 11
The No Operation code provides a means of introducing
delay or a wait sequence into the table operation. In selecting
this code the terminal will be forced into the Report sequence
and provide either an increment signal (INCADRN) or an
interrupt (IRQN) if the Interrupt Always flag in the Instruction
word has been selected.
Bus Select
Code
Definition
00
01
Transmit on bus 0
Transmit on bus 1
Note: Bit 6 of the instruction word is tied low internally.
The required data bus on which transactions take place is
defined by bit 5. In addition to this, this bit defines the bus on
which the Transmitter Self Test operation will be conducted
and the choice of the bus for monitor purposes in Passive
Monitor mode.
Interrupt Condition
Code
Definition
0001
0010
0100
1000
Interrupt if no response
Interrupt if status bit set
Interrupt always
Interrupt if word error
If the terminal detects one of the above conditions and the
appropriate flag is set, the the IRQ line will pulse low for 250ns.
相关PDF资料 |
PDF描述 |
|---|---|
| MA3693 | 1553B Bus Controller/Remote Terminal |
| MA5114 | Radiation hard 1024x4 Bit Static RAM |
| MA7001 | Radiation Hard 512x9 Bit FIFO |
| MA9264 | Radiation Hard 8192x8 Bit Static RAM |
| MAC15S | Sensitive Gate Triacs Silicon Bidirectional Thyristors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MA3693 | 制造商:DYNEX 制造商全称:Dynex Semiconductor 功能描述:1553B Bus Controller/Remote Terminal |
| MA-36AS10C3 | 制造商:Omron Corporation 功能描述:SWITCH,MA-36AS10C3, 1NC, 3M CABLE, SWITCH AND ACTUATOR |
| MA-36AS10CC | 制造商:Omron Corporation 功能描述: |
| MA-36AS10CC5 | 制造商:Omron Corporation 功能描述: |
| MA-36DS10C3 | 制造商:Omron Corporation 功能描述:SWITCH,MA-36DS10C3,1NC,3M CABLE,SWITCH & ACTUATOR |
发布紧急采购，3分钟左右您将得到回复。