- 您现在的位置：买卖IC网 > PDF目录1935 > MAX1042BETX+ (Maxim Integrated Products)IC ADC/DAC 10BIT W/FIFO 36TQFN PDF资料下载
参数资料
| 型号： | MAX1042BETX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/39页 |
| 文件大小： | 0K |
| 描述： | IC ADC/DAC 10BIT W/FIFO 36TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | ADC，DAC |
| 分辨率（位）： | 10 b |
| 采样率（每秒）： | 225k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 电压电源： | 模拟和数字 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
MAX1040/MAX1042/MAX1046/MAX1048
10-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
20
______________________________________________________________________________________
and 7 for timing specifications for starting a scan with
CNVST.
A conversion is not performed if it is requested on a
channel or one of the channel pairs that has been con-
figured as
CNVST or REF2. For channels configured as
differential pairs, the CHSEL0 bit is ignored and the two
pins are treated as a single differential channel. For the
MAX1046/MAX1048, the CHSEL2 bit must be zero.
Channels 4–7 are invalid. Any scans or averages on
these channels can cause corrupt data.
Select scan mode 00 or 01 to return one result per sin-
gle-ended channel and one result per differential pair
within the selected scanning range (set by bits 2 and 1,
SCAN1 and SCAN0), plus one temperature result if
selected. Select scan mode 10 to scan a single input
channel numerous times, depending on NSCAN1 and
NSCAN0 in the ADC averaging register (Table 9).
Select scan mode 11 to return only one result from a
single channel.
Setup Register
Issue a command byte to the setup register to config-
ure the clock, reference, power-down modes, and ADC
single-ended/differential modes. Table 5 details the bits
in the setup-register command byte. Bits 5 and 4
(CKSEL1 and CKSEL0) control the clock mode, acqui-
sition and sampling, and the conversion start. Bits 3
and 2 (REFSEL1 and REFSEL0) set the device for either
internal or external reference. Bits 1 and 0 (DIFFSEL1
and DIFFSEL0) address the ADC unipolar-mode and
bipolar-mode registers and configure the analog input
channels for differential operation.
The ADC reference is always on if any of the following
conditions are true:
1)The FBGON bit is set to one in the reset register.
2)At least one DAC output is powered up and
REFSEL[1:0] (in the setup register) = 00.
3)At least one DAC is powered down through the
100kΩ to VREF and REFSEL[1:0] = 00.
If any of the above conditions exist, the ADC reference
is always on, but there is a 188 clock-cycle delay
before temperature-sensor measurements begin, if
requested.
Table 4. Conversion Register*
BIT
NAME
BIT
FUNCTION
—
7 (MSB)
Set to one to select conversion register.
X
6
Don’t care.
CHSEL2
5
Analog-input channel select
(MAX1040/MAX1042). Set to 0 on
MAX1046/MAX1048.
CHSEL1
4
Analog-input channel select.
CHSEL0
3
Analog-input channel select.
SCAN1
2
Scan-mode select.
SCAN0
1
Scan-mode select.
TEMP
0 (LSB)
Set to one to take a single temp-
erature measurement. The first
conversion result of a scan contains
temperature information.
CHSEL2**
CHSEL1
CHSEL0
SELECTED
CHANNEL
(N)
00
0
AIN0
00
1
AIN1
01
0
AIN2
01
1
AIN3
10
0
AIN4
10
1
AIN5
11
0
AIN6
11
1
AIN7
SCAN1
SCAN0
SCAN MODE
(CHANNEL N IS SELECTED BY
BITS CHSEL2, CHSEL1, AND CHSEL0)
0
Scans channels 0 through N.
01
Scans channels N through the highest
numbered channel.
10
Scans channel N repeatedly. The ADC
averaging register sets the number of
results.
11
No scan. Converts channel N once only.
*
See below for bit details.
**
Channels 4–7 are invalid on the MAX1046/MAX1048. Set
CHSEL2 bit to 0 on those devices.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1057BETM+T | IC ADC/DAC 10BIT 48-TQFN-EP |
| MAX11041ETC+T | IC REMOTE CTRLR WIRED 12-TQFN |
| MAX11043ATL+T | IC ADC 16BIT W/DAC 40-TQFN-EP |
| MAX11359AETL+T | IC DAS SYSTEM 16BIT 40-TQFN |
| MAX115CAX+ | IC DAS SYSTEM 12BIT 36-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1042BETX+ | 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns & GPIO Port RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX1042BETX+T | 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns & GPIO Port RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX1042BETX-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX1043 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports |
| MAX1043BETX | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
发布紧急采购，3分钟左右您将得到回复。