参数资料
型号: MAX11008EVKIT+
厂商: Maxim Integrated
文件页数: 55/67页
文件大小: 0K
描述: KIT EVAL FOR MAX11008 BIAS CTLR
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
类型: 偏压控制器
适用于相关产品: MAX11008
已供物品: 板,模块
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
Table 13d. V GATE _ Calculation Trigger Condition
SOFTWARE CONFIGURATION
SETTINGS
V GATE_ CALCULATION TRIGGER CONDITIONS
TCOMP_ = 1
APCCOMP_ = 1
APCSRC_1 = 0
APCSRC_0 = 0
?
?
?
Temperature measurements vary enough to exceed the hysteresis settings
A write command to the APC_ Parameter register
A write command to the VSET register through the serial interface
TCOMP_ = 1
APCCOMP_ = 1
APCSRC_1 = 1
APCSRC_0 = X
TCOMP_ = 1
APCCOMP_ = 0
APCSRC_1 = X
APCSRC_0 = X
TCOMP = 0
APCCOMP = 1
APCSRC_1 = 0
APCSRC_0 = 0
TCOMP = 0
APCCOMP = 1
APCSRC_1 = 1
APCSRC_0 = X
TCOMP = 0
APCCOMP = 0
APCSRC_1 = X
APCSRC_0 = X
X = Don’t care.
? Temperature measurements vary enough to exceed the hysteresis settings
? Current-sense measurements or ADCIN_ samples vary enough to cause a new LUT
value to be retrieved (depends on PSIZE and INT values in the LUT Configuration
registers)
? A write command to the VSET register through the serial interface
? Temperature measurements vary enough to exceed the hysteresis settings
? A write command to the VSET register through the serial interface
? A write command to the APC_ register through the serial interface
? A write command to the VSET register through the serial interface
? Current-sense measurements vary enough to exceed the hysteresis settings
? A write command to the VSET register through the serial interface
? A write command to the VSET register through the serial interface
Set SELFTIME to 1 and DOCAL to 1 to perform calibra-
tions of PGA1 and PGA2 on a self-timed periodic basis
(approximately every 13ms). When SELFTIME is set to
0, writing to PGACAL with DOCAL set to 1 manually
triggers PGA calibration.
ADC Conversion Register (ADCCON) (Write Only)
Write to the ADC Conversion register to select which
channels are converted and to set the ADC for continu-
ous conversion of each selected channel (see Table
20). Set CONCONV to 1 to configure the ADC to per-
form continuous conversions of the selected channels.
Bits D[6:0] select which channels are converted. Select
which channel is to be converted by setting the corre-
sponding bit to 1. Any channel that is set to 0 will not
be converted. Depending on the ADC clock mode that
is selected in the Hardware Configuration register (see
the Internally Timed Acquisitions and Conversions sec-
tion and Table 11), writing to the ADC Conversion reg-
ister initiates an ADC conversion of the selected
channel or the next selected channel in the sequence if
more than one channel is selected (see the ADC
Conversion Scheduling section). Bits D[15:8] are don’t-
care bits.
______________________________________________________________________________________
55
相关PDF资料
PDF描述
MAX1471EVSYS-315 EVAL KIT FOR MAX1471 315MHZ
MAX1471EVSYS-433 EVAL KIT FOR MAX1471 433MHZ
MDEV-LICAL-MS DEV SYSTEM MS SERIES 418MHZ
MAX2622EVKIT EVAL KIT
MAX2751EVKIT EVAL KIT
相关代理商/技术参数
参数描述
MAX11008EVKIT+ 功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX1100CWG 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1101 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA
MAX11014 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014_08 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers