- 您现在的位置：买卖IC网 > PDF目录15535 > MAX11080GUU/V+T (Maxim Integrated Products)IC LI/BATTERY MANAGEMENT 38TSSOP PDF资料下载
参数资料
| 型号： | MAX11080GUU/V+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/29页 |
| 文件大小： | 0K |
| 描述： | IC LI/BATTERY MANAGEMENT 38TSSOP |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 电池监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 6 V ~ 72 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 38-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
12-Channel, High-Voltage
Battery-Pack Fault Monitors
TOP OF
CELL STACK
22 ?
R LIMIT
22 ?
TO GND U
INPUT
between charge and discharge conditions. Next, the
linear regulator has high PSRR to produce a clean low-
voltage power supply for the internal circuitry. This
allows DCIN to be connected directly to the stack volt-
age. Finally, GND U serves two purposes. It supplies the
SEE THE APPLICATION CIRCUIT
DIAGRAM FOR PROPER
5k ?
100k ?
internal charge pump with its power and acts as the ref-
erence ground for the upper alarm communication port.
CONNECTION LOCATION
C DCIN
0.1 μ F
80V
SMCJ70
TO DCIN
INPUT
The charge pump creates a secondary low-voltage
supply that is referenced to GND U . Because the level-
shifted supply VDD U is referenced to GND U , the entire
upper alarm communication port glides smoothly on
GND U and it is effectively immune to noise on GND U .
Figure 14. Battery Module Surge and Overvoltage Protection
Circuit
the SMCJ70 on the DCIN connection point. This protec-
tion circuit also helps to reduce power spikes that can
occur during the insertion of the battery cells. During
negative voltage excursions, the protection circuit stores
enough charge to power the regulator through the tran-
sient. Figure 14 shows the clamp configuration to protect
the DCIN supply input.
The DCIN input contains a comparator circuit to detect an
open circuit on this pin for fault-management purposes.
Whenever a nominal voltage of two silicon diode drops
appears between C12 and DCIN following the power-up
sequence, the ALRM L output is asserted as a fault indica-
tion. This voltage drop must appear for at least the delay
time set by C DLY to result in a fault. The voltage drop from
C12 to DCIN during normal operation should be kept at
no more than 0.5V to prevent erroneous tripping of the
DCIN open-circuit comparator under worst-case circum-
stances (lowest silicon diode forward bias voltage). The
diode D DCIN is used to supply the transient current
demanded at startup by the decoupling circuit. In parallel
with this diode, R DCIN provides the supply path during
normal operation. It is selected to be 5k ? so that the max-
imum voltage drop between C12 and DCIN is about
0.25V with nominal supply currents.
High-power batteries are often used in noisy environ-
ments subject to high dV/dt or dI/dt supply noise and
EMI noise. For example, the supply noise of a power
inverter driving a high horse-power motor produces a
large square wave at the battery terminals, even though
the battery is also a high-power battery. Typically, the
battery dominates the task of absorbing this noise, since
it is impractical to put hundreds of farads at the inverter.
The MAX11080/MAX11081 are designed with several
mechanisms to deal with extremely noisy environments.
First, the major power-supply inputs that see the full
battery-stack voltage are 80V tolerant. This is high
enough to handle the large voltage changes on the bat-
tery stack that can occur when the batteries transition
The upper alarm signal is internally shifted down to
AGND level where it is processed by the digital logic.
There are two connection methods that can be used for
GND U depending on application requirements.
For the top module in a system, or where GND U cannot
be DC-coupled to the next higher module for other rea-
sons, GND U should be connected to the same location
as DCIN. This connection is valid as long as the voltage
difference between the top of Stack(n) and the bottom
of Stack(n+1) during worst-case conditions does not
exceed the margin of the alarm pin signaling levels.
When GND U is not DC-coupled to the far side of the
bus bar, it can be AC-coupled to the far side to main-
tain alarm communication when the bus bar is open-cir-
cuit. In that case, the two sides of the AC-coupling
capacitor can be at different DC potentials, but the
alarm communication signal continues to be passed
across the capacitor connection. It is recommended
that an AC- or DC-coupled version of GND U is paired
with the alarm signal through the communication bus
wiring, possibly by twisted pair wire, for maximum noise
immunity and minimum emissions.
The preferred connection to reject noise between mod-
ules is when a DC connection can be made from GND U
to AGND of the next module. It is again recommended
that the DC-coupled GND U signal is routed adjacent to
the alarm signal as part of the communication bus for
maximum noise immunity and minimum emissions.
Shutdown Control
The SHDN pin connections of the MAX11080/MAX11081
operate in a manner that allows the shutdown/wake-up
command to trickle up through the series of daisy-
chained packs. Because the internal linear regulator is
powered down during shutdown, the shutdown function
must operate when V AA is absent and, therefore, it can-
not depend on a Schmitt trigger input. A special low-cur-
rent, high-voltage circuit is used to detect the state of the
SHDN pin. The shutdown pin has a +2.1V minimum
threshold for the inactive state. When SHDN > 2.1V, the
MAX11080/MAX11081 turn on and begin regulating V AA ,
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX11081GUU+T | IC FAULT MON BATT 12CH 38-TSSOP |
| MAX11081GUU/V+T | IC FAULT MON BATT 12CH 38TSSOP |
| AIUR-10-330K | INDUCTOR POWER 33UH 10% T/H |
| MAX11080GUU+T | IC LI/BATTERY MANAGEMENT 38TSSOP |
| V48C15C75B3 | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11080IUU+ | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX11080IUU+T | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX11081GUU/V+ | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX11081GUU/V+T | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX11081GUU+ | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。