- 您现在的位置：买卖IC网 > PDF目录15535 > MAX11080GUU/V+T (Maxim Integrated Products)IC LI/BATTERY MANAGEMENT 38TSSOP PDF资料下载
参数资料
| 型号： | MAX11080GUU/V+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/29页 |
| 文件大小： | 0K |
| 描述： | IC LI/BATTERY MANAGEMENT 38TSSOP |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 电池监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 6 V ~ 72 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 38-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
12-Channel, High-Voltage
Battery-Pack Fault Monitors
CP+
S1B
150 I
1k I
SHDN
DEVICE
(n)
5.6V
100nF
5.6V
68nF
200k I
DEVICE
(n+1)
GND U
Figure 17. Shutdown Circuit Interface
and then VDD U . If SHDN < 0.6V, the MAX11080/
MAX11081 shut down.
Figure 17 shows the shutdown circuit interface of two
daisy-chain devices.
When SHDN is high for device n, the charge pump is
ALRM U
AGND
enabled and begins to charge the capacitors in the
interface circuit. When the voltage of the SHDN pin for
device (n+1) rises above the VIH threshold, that device
begins its power-up sequence. This action propagates
up the daisy-chain until the last battery module is
VAA
SHDN
5 BIT UP
FULL FLAG
D
CLK
Q
FMEA FLAG
INTERNAL ALARM
SIGNAL
ALRM L
enabled. Conversely, pulling SHDN to AGND powers
down a module and thus propagates the power-down
to all higher daisy-chained modules as the charge on
their SHDN capacitors is dissipated. The zener diodes
provide additional ESD protection. The filter capacitors
COUNTER
RST
PORb
and resistors are sized to provide robust noise immuni-
ty. The diode from the CP+ pin should be S1B or a simi-
lar low-leakage type for high-temperature stability.
The SHDN pin has a weak internal pulldown resistor on
the order of 12M ? . A 200k ? or similar resistor from SHDN
to AGND should be installed to ensure that the SHDN pin
is pulled low when the active SHDN signal is propagated
up the daisy-chain bus. The resistor is not needed for
applications that tie SHDN high at all times. The typical
SHDN rising edge propagation time from one daisy-
chained module to the next is 1.5ms.
For FMEA detectability, the SHDN pin is designed to
detect logic transitions that could be indicative of a
short circuit to the ALRM L pin. The SHDN pin circuit
shown in Figure 18 provides some immunity for rare
glitches at the SHDN pin, such as those during power-
up, that are not a result of a short to ALRM L . The SHDN
pin signal is fed as a clock to a 5-bit counter. When the
counter reaches the maximum count of 32, the full flag
is set and acts as a clock to a D flip-flop. When the D
flip-flop is clocked, its output goes high to signal the
FMEA fault condition and trigger the alarm. In this way,
the device goes into the alarm state only after 32 pulses
Figure 18. Internal FMEA SHDN Pin Functionality Circuit
on the SHDN pin have occurred. To clear the FMEA
fault state, a POR of the device must be activated. The
application circuit should ensure that the SHDN pin is
glitch free and only toggles when a shutdown or power-
down event is intended. This FMEA detection circuit
should not be considered as a provision to filter out
noise or glitches on the SHDN pin.
C1 Input Absolute Maximum Rating
The C1 input is limited to V DCIN - 0.6V above AGND or
a maximum of 20V if the SHDN pin is asserted. If an
application requires that the 20V restriction be removed
during active shutdown, then a 4.0V zener diode can
be added from V AA to AGND. This protects V AA and
allows the C1 input to go to V DCIN - 0.6V regardless of
the SHDN state. It also allows the differential C1 to C0
voltage to range from -0.3V to +80V.
Cell-Connection and Detection
An individual MAX11080/MAX11081 can be connected to
as many as 12 series-connected cells. To accommodate
configurations with fewer cells, unused cell inputs must be
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX11081GUU+T | IC FAULT MON BATT 12CH 38-TSSOP |
| MAX11081GUU/V+T | IC FAULT MON BATT 12CH 38TSSOP |
| AIUR-10-330K | INDUCTOR POWER 33UH 10% T/H |
| MAX11080GUU+T | IC LI/BATTERY MANAGEMENT 38TSSOP |
| V48C15C75B3 | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11080IUU+ | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX11080IUU+T | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX11081GUU/V+ | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX11081GUU/V+T | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX11081GUU+ | 功能描述:电池管理 12 Ch Hi Volt Batt Pack Fault Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。