- 您现在的位置：买卖IC网 > PDF目录1935 > MAX11359AETL+T (Maxim Integrated Products)IC DAS SYSTEM 16BIT 40-TQFN PDF资料下载
参数资料
| 型号： | MAX11359AETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 29/67页 |
| 文件大小： | 0K |
| 描述： | IC DAS SYSTEM 16BIT 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 数据采集系统（DAS） |
| 分辨率（位）： | 16 b |
| 采样率（每秒）： | 512 |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 电压电源： | 模拟和数字 |
| 电源电压： | 1.8 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
MAX11359A
16-Bit Data-Acquisition System with ADC, DAC,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
35
Maxim Integrated
The ADC register configures the ADC and starts
a conversion.
ADCE: ADC power-enable bit. ADCE = 1 powers up
the ADC, and ADCE = 0 powers down the ADC.
STRT: ADC start bit. STRT = 1 resets the registers
inside the ADC filter and initiates a conversion or cali-
bration. The conversion begins immediately after the
16th ADC control bit is clocked by the rising edge of
SCLK. The initial conversion requires four conversion
cycles for valid output data. If CONT = 0 when STRT is
asserted, the ADC stops after a single conversion and
holds the result in the DATA register. If CONT = 1 when
STRT is asserted, the ADC performs continuous conver-
sions at the rate specified by the RATE<2:0> bits until
CONT is deasserted or ADCE is deasserted, powering
down the ADC. The STRT bit is automatically deasserted
after the initial conversion is complete (four conversion
cycles; the ADC status bit ADD in the STATUS register
asserts.) The current ADC configurations are not affect-
ed if the ADC register is written with STRT = 0. This
allows the ADC and mux configurations to be updated
simultaneously with the S bit in the MUX register.
BIP: Unipolar/bipolar bit. Set BIP = 0 for unipolar mode
and BIP = 1 for bipolar mode. Unipolar-mode data is
unsigned binary format and bipolar is two’s complement.
See the
ADC Transfer Functions section for more details.
POL: Polarity flipper bit. POL = 1 flips the polarity of the
differential signal to the ADC and the input to the signal-
detect comparator (SDC). POL = 0 sets the positive mux
output to the positive ADC and SDC inputs, and the neg-
ative mux output to the negative ADC and SDC inputs.
POL = 1 sets the positive mux output to the negative
ADC and SDC inputs, and the negative mux output to
the positive ADC and SDC inputs.
CONT: Continuous conversion bit. CONT = 1 enables
continuous conversions following completion of the first
conversion or calibration(s) initiated by the STRT or S
bit. Set CONT = 0 while asserting the STRT bit, or prior
to asserting the S bit to perform a single conversion or to
prevent conversions following a calibration. Set CONT =
0 to abort continuous conversions already in progress.
When the ADC is stopped in this way, the last complete
conversion result remains in the DATA register and the
internal ADC state information is lost. Asserting the
CONT bit does not restart the ADC, but results in contin-
uous conversions once the ADC is restarted with the
STRT or S bit.
ADCREF: ADC reference source bit. Set ADCREF = 0
to select REF as the ADC reference. Set ADCREF = 1
to select AVDD as the ADC reference. To measure the
AVDD voltage without having to attenuate the supply
voltage, select REF and AGND as the differential inputs
to the ADC, with POL = 0 and while ADCREF = 1.
GAIN<1:0>: ADC gain-setting bits. These two bits
select the gain of the ADC as shown in Table 5.
MSB
LSB
ADCE
STRT
BIP
POL
CONT
ADCREF
GAIN<1:0>
RATE<2:0>
MODE<2:0>
X
ADC Register (Power-On State: 0000 0000 0000 00XX)
Register Bit Descriptions
GAIN SETTING (V/V)
GAIN1
GAIN0
10
0
20
1
41
0
81
1
Table 5. Setting the Gain of the ADC
相关PDF资料 |
PDF描述 |
|---|---|
| MAX115CAX+ | IC DAS SYSTEM 12BIT 36-SSOP |
| MAX1221BETX+T | IC ADC/DAC 12BIT W/FIFO 36TQFNEP |
| MAX1257BETM+T | IC ADC/DAC 12BIT 48-TQFN |
| MAX125CCAX+D | IC DAS 14BIT 2X4CH 36-SSOP |
| MAX1271AENG+ | IC ADC 12BIT 8CH 24-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1135BCAP | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1135BCAP+ | 功能描述:模数转换器 - ADC 16-Bit 150ksps 3.3V Single Supply RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1135BCAP+T | 功能描述:模数转换器 - ADC 16-Bit 150ksps 3.3V Single Supply RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1135BCAP-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1135BEAP | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。