参数资料
| 型号： | MAX11637EEE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 8CH 16QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 12 |
| 采样率（每秒）： | 300k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 667mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极；4 个差分，单极；4 个差分，双极 |
MAX11634–MAX11637
12-Bit, 300ksps ADCs with Differential
Track/Hold, and Internal Reference
______________________________________________________________________________________
21
Partial Reads and Partial Writes
If the first byte of an entry in the FIFO is partially read
(CS is pulled high after fewer than eight SCLK cycles),
the second byte of data that is read out contains the
next 8 bits (not b[7:0]). The remaining bits are lost for
that entry. If the first byte of an entry in the FIFO is read
out fully, but the second byte is read out partially, the
rest of the entry is lost. The remaining data in the FIFO
is uncorrupted and can be read out normally after tak-
ing CS low again, as long as the four leading bits (nor-
mally zeros) are ignored. Internal registers that are
written partially through the SPI contain new values,
starting at the MSB up to the point that the partial write
is stopped. The part of the register that is not written
contains previously written values. If CS is pulled low
before EOC goes low, a conversion cannot be complet-
ed and the FIFO is corrupted.
Transfer Function
Figure 8 shows the unipolar transfer function for single-
ended or differential inputs. Figure 9 shows the bipolar
transfer function for differential inputs. Code transitions
occur halfway between successive-integer LSB values.
Output coding is binary, with 1 LSB = VREF/4096 for
unipolar and bipolar operation, and 1 LSB = 0.125°C
for temperature measurements.
Layout, Grounding, and Bypassing
For best performance, use PC boards. Do not use wire-
wrap boards. Board layout should ensure that digital
and analog signal lines are separated from each other.
Do not run analog and digital (especially clock) signals
parallel to one another or run digital lines underneath the
MAX11634–MAX11637 package. High-frequency noise
in the VDD power supply can affect performance.
Bypass the VDD supply with a 0.1F capacitor to GND,
close to the VDD pin. Minimize capacitor lead lengths for
best supply-noise rejection. If the power supply is very
noisy, connect a 10
resistor in series with the supply to
improve power-supply filtering.
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line can be either a best-straight-line fit or a line
drawn between the end points of the transfer function,
once offset and gain errors have been nullified. INL for
the MAX11634–MAX11637 is measured using the end-
point method.
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between
an actual step width and the ideal value of 1 LSB. A
DNL error specification of less than 1 LSB guarantees
no missing codes and a monotonic transfer function.
Aperture Jitter
Aperture jitter (tAJ) is the sample-to-sample variation in
the time between the samples.
Aperture Delay
Aperture delay (tAD) is the time between the rising
edge of the sampling clock and the instant when an
actual sample is taken.
CS
DOUT
SCLK
DIN
EOC
MSB1
LSB1
MSB2
(ACQUISITION1)
(ACQUISITION2)
(CONVERSION1)
(CONVERSION BYTE)
EXTERNALLY TIMED ACQUISITION, SAMPLING AND CONVERSION WITHOUT CNVST.
Figure 7. Clock Mode 11
相关PDF资料 |
PDF描述 |
|---|---|
| MAX11643EEG+T | IC ADC 8BIT 8CH 24QSOP |
| MAX11645EUA+T | IC ADC 12BIT I2C/SRL 1CH 8UMAX |
| MAX11647EUA+T | IC ADC 10BIT I2C 94.4KSPS 8UMAX |
| MAX1166BEUP+ | IC ADC 16BIT 165KSPS 20-TSSOP |
| MAX1168BCEG+ | IC ADC 16BIT 200KSPS 24-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11638EEE+ | 功能描述:模数转换器 - ADC 8Ch 8-Bit 300ksps w/FIFO & Int Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11638EEE+T | 功能描述:模数转换器 - ADC 8Ch 8-Bit 300ksps w/FIFO & Int Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11639EEE+ | 功能描述:模数转换器 - ADC 8Ch 8-Bit 300ksps w/FIFO & Int Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11639EEE+T | 功能描述:模数转换器 - ADC 8Ch 8-Bit 300ksps w/FIFO & Int Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11642EEG+ | 功能描述:模数转换器 - ADC 16Ch 8-Bit 300ksps w/FIFO & Int Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。