- 您现在的位置：买卖IC网 > PDF目录17008 > MAX1403EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX1403 PDF资料下载
参数资料
| 型号： | MAX1403EVKIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/36页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX1403 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 18 |
| 采样率（每秒）： | 480 |
| 数据接口： | 串行 |
| 输入范围： | ±VREF/增益 |
| 在以下条件下的电源（标准）： | 16.9mW @ 480SPS |
| 工作温度： | 0°C ~ 70°C |
| 已用 IC / 零件： | MAX1403 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Analog Filtering
The digital filter does not provide any rejection close to
the harmonics of the modulator sample frequency.
However, due to the high oversampling ratio of the
MAX1403, these bands occupy only a small fraction of
the spectrum and most broadband noise is filtered.
Therefore, the analog filtering requirements in front of
the MAX1403 are considerably reduced compared to a
conventional converter with no on-chip filtering. In addi-
tion, because the part’s common-mode rejection of
90dB extends out to several kHz, common-mode noise
susceptibility in this frequency range is substantially
reduced.
Depending on the application, it may be necessary to
provide filtering prior to the MAX1403 to eliminate
unwanted frequencies the digital filter does not reject. It
may also be necessary in some applications to provide
additional filtering to ensure that differential noise sig-
nals outside the frequency band of interest do not satu-
rate the analog modulator.
If passive components are placed in front of the
MAX1403, when the part is used in unbuffered mode,
ensure that the source impedance is low enough not to
introduce gain errors in the system (Tables 13a–13d).
This can significantly limit the amount of passive anti-
aliasing filtering that can be applied in front of the
MAX1403 in unbuffered mode. However, when the part
is used in buffered mode, large source impedances will
simply result in a small DC offset error (a 1k
source
resistance will cause an offset error of less than 10V).
Therefore, where any significant source impedances
are required, Maxim recommends operating the part in
buffered mode.
Calibration Channels
Two fully differential calibration channels allow mea-
surement of the system gain and offset errors. Connect
the CALOFF channel to 0V and the CALGAIN channel
to the reference voltage. Average several measure-
ments on both CALOFF and CALGAIN. Subtract the
average offset code and scale to correct for the gain
error. This linear calibration technique can be used to
remove errors due to source impedances on the analog
input (e.g., when using a simple RC anti-aliasing filter
on the front end).
Applications Information
SPI Interface (68HC11, PIC16C73)
Microprocessors with a hardware SPI (serial peripheral
interface) can use a 3-wire interface to the MAX1403
(Figure 12). The SPI hardware generates groups of
eight pulses on SCLK, shifting data in on one pin and
out on the other pin.
For best results, use a hardware interrupt to monitor the
INT pin and acquire new data as soon as it is available.
If hardware interrupts are not available, or if interrupt
latency is longer than the selected conversion rate, use
the FSYNC bit to prevent automatic measurement while
reading the data output register.
The example code in Listing 1 shows how to interface
with the MAX1403 using a 68HC11. System-dependent
initialization code is not shown.
MAX1403
+3V, 18-Bit, Low-Power, Multichannel,
Oversampling (Sigma-Delta) ADC
30
______________________________________________________________________________________
VDD
SS
INTERRUPT
SCK
MISO
MOSI
RESET
INT
SCLK
DOUT
DIN
CS
VDD
68HC11
MAX1403
Figure 12. MAX1403 to 68HC11 Interface
-160
-140
-100
-120
-80
-60
-20
-40
0
406080
20
100 120 140 160 180 200
FREQUENCY (Hz)
GAIN
(dB)
fCLKIN = 2.4576MHz
MF1, 0 = 0
FS1, 0 = 0
fN = 50Hz
Figure 11. Frequency Response of the SINC3 Filter
(Notch at 50Hz)
相关PDF资料 |
PDF描述 |
|---|---|
| GEC36DRES-S13 | CONN EDGECARD 72POS .100 EXTEND |
| VI-2W4-EY | CONVERTER MOD DC/DC 48V 50W |
| 380LX121M400J022 | CAP ALUM 120UF 400V 20% SNAP |
| SDR7045-470K | INDUCTOR POWER 47UH 10% SMD |
| AC1059 | SOCKET FOR MODEL AD210 IC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1403EVL11 | 功能描述:数据转换 IC 开发工具 MAX1403 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX1403EVSYSTEM | 制造商:Maxim Integrated Products 功能描述:EVALUATION SYSTEM FOR THE MAX1403 - Boxed Product (Development Kits) |
| MAX1406C/D | 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| MAX1406CAE | 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| MAX1406CAE+ | 功能描述:RS-232接口集成电路 15kV ESD-Protected 230kbps RS-232 LD/Rc RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
发布紧急采购，3分钟左右您将得到回复。