- 您现在的位置：买卖IC网 > PDF目录2008 > MAX1415AEWE+T (Maxim Integrated Products)IC ADC 16BIT DELTA SIGMA 16-SOIC PDF资料下载
参数资料
| 型号： | MAX1415AEWE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/36页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT DELTA SIGMA 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 位数： | 16 |
| 采样率（每秒）： | 500 |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 762mW |
| 电压电源： | 单电源 |
| 工作温度： | -45°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个差分，单极；2 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Internal Oscillator Mode
In internal oscillator mode (INTCLK = 1), set the CLK bit
in the clock register (Table 12) to 0 to operate at a clock
frequency of 1MHz, or set CLK to 1 for a frequency of
2.4576MHz. The CLKDIV bit is not used in this mode.
Internal-Clock Startup Time
The internal clock requires time to stabilize during
power-on reset. This startup time is dependent on the
internal-clock frequency (see the Typical Operating
Characteristics section). The typical startup time for the
internal oscillator is less than 35s, while the external
oscillator startup time when using a crystal or resonator
is in the order of milliseconds.
External Oscillator
The oscillator requires time to stabilize when enabled.
Startup time for the oscillator depends on supply voltage,
temperature, load capacitances, and center frequency.
Depending on the load capacitance, a 1M
feedback
resistor across the crystal can reduce the startup time
(Figure 7). The MAX1415/MAX1416 were tested with an
ECS-24-32-1 (2.4576MHz crystal) and an ECS-49-20-1
(4.9152MHz crystal) (see the Typical Operating Char-
acteristics section). When the external oscillator is
enabled, the supply current is typically 67A with a 3V
supply and 227A with a 5V supply.
Serial Digital Interface
The MAX1415/MAX1416 interface is fully compatible with
SPI-, QSPI-, and MICROWIRE-standard serial interfaces.
The serial interface provides access to seven on-chip
registers. The registers are 8, 16, and 24 bits in size.
Drive
CS low to transfer data in and out of the
MAX1415/MAX1416. Clock in data at DIN on the rising
edge of SCLK. Data at DOUT changes on the falling
edge of SCLK and is valid on the rising edge of SCLK.
DIN and DOUT are transferred MSB first. Drive
CS high
to force DOUT high impedance and cause the
MAX1415/MAX1416 to ignore any signals on SCLK and
DIN. Connect
CS low for 3-wire operation. Figures 8
and 9 show the timings for write and read operations,
respectively.
On-Chip Registers
The MAX1415/MAX1416 contain seven internal registers
(Figure 10), which are accessed by the serial interface.
These registers control the various functions of the device
and allow the results to be read. Table 7 lists the address,
power-on default value, and size of each register.
The first of these registers is the communications register.
The 8-bit communications register controls the acquisi-
tion-channel selection, whether the next data transfer is a
read or write operation, and which register is to be
accessed. The second register is the 8-bit setup register,
which controls calibration modes, gain setting,
unipolar/bipolar inputs, and buffered/unbuffered modes.
The third register is the 8-bit clock register, which sets the
digital filter characteristics and the clock control bits. The
fourth register is the 16-bit data register, which holds the
output result. The 24-bit offset and gain registers store the
calibration coefficients for the MAX1415/MAX1416. The 8-
bit test register is used for factory testing only.
MAX1415/MAX1416
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADCs
______________________________________________________________________________________
23
CRYSTAL OR
CERAMIC
RESONATOR
CL
CLKIN
CLKOUT
OPTIONAL
1M
MAX1415
MAX1416
Figure 7. Using a Crystal or Ceramic Oscillator
CS
t2
t6
t9
t10
SCLK
MSB
LSB
DIN
Figure 8. Write Timing Diagram
t2
t4
t5
t3
t8
t6
t7
t1
SCLK
MSB
LSB
DOUT
CS
DRDY
Figure 9. Read Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1421CCM+D | IC ADC 12BIT 40MSPS 48LQFP |
| MAX1426EAI+T | IC ADC 10BITS 10MSPS 28SSOP |
| MAX1434ECQ+D | IC ADC 10BIT 50MSPS 100-TQFP |
| MAX1444EHJ+T | IC ADC 10BIT 40MSPS 32-TQFP |
| MAX1499ECJ+ | IC ADC 3 1/2DIG W/LED DVR 32TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1415ENE | 制造商:Maxim Integrated Products 功能描述:16-BIT, LOW-POWER, 2-CHANNEL, SIGMA-DELTA ADC - Rail/Tube |
| MAX1415EPE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1415EPE+ | 功能描述:模数转换器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1415EUE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1415EUE+ | 功能描述:模数转换器 - ADC 16-Bit 2Ch .5ksps 1.75V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。