- 您现在的位置：买卖IC网 > PDF目录1936 > MAX1464AAI+T (Maxim Integrated Products)IC SENSOR SIGNAL COND 28-SSOP PDF资料下载
参数资料
| 型号： | MAX1464AAI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/47页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR SIGNAL COND 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 类型： | 信号调节器 |
| 输入类型： | 模拟 |
| 输出类型： | 逻辑 |
| 接口： | SPI |
| 电流 - 电源： | 890µA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
MAX1464
Low-Power, Low-Noise Multichannel
Sensor Signal Processor
17
Maxim Integrated
long lengths of wire. The unity-gain buffer configuration
is automatically selected, and it provides the DAC out-
put signal directly to the device pin OUTnLG. With the
large op amp selected, the small op amp can be used
as an independent device for external circuit applica-
tions when the PWM is disabled. Alternatively, the PWM
can also be enabled to drive the OUTnSM device pin,
in which case the small op amp is OFF.
Selecting the small op amp as the DAC output driver
device is useful for routing the output signal to other cir-
cuits in an embedded control system with high-imped-
ance load connections. The unity-gain buffer configuration
is automatically selected, and it provides the DAC output
signal directly to the device pin OUTnSM. With the small
op amp selected, the large op amp can be used as an
independent device for external circuit applications when
the PWM is disabled. Alternatively, the PWM can also be
enabled to drive the OUTnLG device pin, in which case
the large op amp is OFF.
The DAC has two reference voltage sources available by
selection, VDD and VREF input. When the external refer-
ence is selected (VREF), the actual DAC reference is 2 x
VREF. See VREF to 2.5V for nominal operation. The output
of the DAC is a voltage proportional to the reference volt-
age selected, where the proportionality scaling (DAC
input) is set in the data input register DOPn_Data.
The DOP module also provides a 12-bit digital PWM
output. At a nominal 4MHz frequency, the frequency of
the PWM is 122Hz (PWM period = 8.192ms). The DAC
and the PWM share the same input register,
DOPn_Data, where the PWM uses the 12 MSBs, in
two’s-complement format. An input of 000Xh (4 LSBs
are ignored) outputs a 50% duty cycle waveform at the
selected output pin (either OUTnSM or OUTnLG). The
PWM bit weight is 2s, at a nominal frequency of 4MHz.
The minimum duty cycle is obtained when the input is
800Xh (duty cycle is 0 / 4096 = 0), and the maximum
duty cycle at 7FFXh (duty cycle is 4095 / 4096 =
99.98%). A new PWM input word is only effective at the
end of a current PWM cycle, therefore preventing PWM
glitches on the output.
Either the small or the large op amp in the DOP module
can also be selected as an uncommitted op amp in the
MAX1464. The op amps can be configured as a unity-
gain buffer, where the output is internally connected to the
negative terminal of the op amp, or a stand-alone op amp,
where both AMPnM and AMPnP can be externally con-
nected for various analog functions. In the case of a buffer,
the device pin AMPnM is in high-impedance mode, as the
feedback loop around the op amp is connected internally.
DAC
10h OR 13h
DOPn_Data
12h OR 15h
DOPn_Config
30h
OpAmp_Config
11h OR 14h
DOPn_Control
REF
PWM
SW0
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
SW9
2 x VREF
VDD
OUTnSM
AMPnM
AMPnP
OUTnLG
SW10
SW11
SM
LG
Figure 5. DOP1 and DOP2 Modules
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1474AXT+T | IC ELECTRONIC CAPACITOR SC70-6 |
| MAX14753EUE+T | IC MULTIPLEXER DUAL 4X1 16TSSOP |
| MAX14756EUE+T | IC ANLG SWITCH SPST QUAD 16TSSOP |
| MAX14759ETA+ | IC SWITCH ANALOG 8-TDFN-EP |
| MAX14764ETA+T | IC ANALOG SWITCH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1464CAI | 功能描述:数字信号处理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MAX1464CAI+ | 功能描述:数字信号处理器和控制器 - DSP, DSC Low-Power Low-Noise Multichannel Sensor Signal Processor RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MAX1464CAI+T | 功能描述:数字信号处理器和控制器 - DSP, DSC Low-Power Low-Noise Multichannel Sensor Signal Processor RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MAX1464CAI-T | 功能描述:数字信号处理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MAX1464EAI | 功能描述:数字信号处理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。