- 您现在的位置：买卖IC网 > PDF目录11817 > MAX14830ETM+T (Maxim Integrated Products)IC UART PDF资料下载
参数资料
| 型号： | MAX14830ETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/68页 |
| 文件大小： | 0K |
| 描述： | IC UART |
| 产品培训模块： | Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
27
Maxim Integrated
Quad Serial UART with 128-Word FIFOs
MAX14830
Transmitter Flow Control
When auto transmitter control (FlowCtrl[5:4]) is enabled,
the receiver compares all received words with the XOFF
and XON characters. If an XOFF character is received,
the MAX14830 halts its transmitter from sending further
data. The receiver is not affected and continues reception.
Upon receiving XON, the transmitter then restarts sending
data. The received XON and XOFF characters are filtered
out and are not put into the Receive FIFO, as they do not
have significance to the higher layer protocol. An inerrupt
is not generated.
Turn the transmitter off (MODE1[1] = 1) before enabling
transmitter control.
Receiver Overflow Control
When auto receiver overflow control (FlowCtrl[7:6]) is
enabled, the MAX14830 automatically sends XOFF and
XON control characters to the far end UART to avoid
receiver overflow. XOFF1/XOFF2 is/are sent when the
Receive FIFO fill level reaches the HALT value set in the
FlowLvl register. When the host controller reads data
from the Receive FIFO to a level equal to the RESUME
level programmed into the FlowLvl register, XON1/XON2
is/are automatically sent to the far end station to signal it
to resume data transmission.
XON1/XOFF1 is transmitted before XON2/XOFF2 when
dual character (XON1 and XON2/XOFF1 and XOFF2)
flow control is enabled.
Power-Up and IRQ
IRQ has two functions. During normal operation
(MODE1[7] = 1), IRQ operates as a hardware interrupt
output, whereby the IRQ is active when an interrupt is
pending. An IRQ interrupt can only be produced during
normal operation if at least one of the IRQEn interrupt
enable bits are enabled.
During power-up or following a reset, IRQ has a different
function. It is held low until the MAX14830 is ready for
programming following an initialization delay. Once IRQ
goes high, the MAX14830 is ready to be programmed.
The MODE1[7]: IRQSel bit should then be set to enable
normal IRQ interrupt operation.
In polled mode, the DIVLSB register can be polled to
check whether the MAX14830 is ready for operation. If
the controller gets a valid response from DIVLSB, then
the MAX14830 is ready for operation.
Shutdown Mode
Pull RST to DGND to enter shutdown mode. Shutdown
mode is the lowest power consumption mode. In shut-
down mode, all of the MAX14830 circuitry is off. This
includes the SPI/I2C interface, the registers, the FIFOs,
and clocking circuitry. The LDO is on in shutdown mode.
When the RST input is high, the MAX14830 exits shut-
down mode. The chip initialization is completed when the
MAX14830 sets IRQ to logic-high.
The MAX14830 needs to be reprogrammed following a
shutdown.
Interrupt Structure
The structure of the interrupt is shown in Figure 16.
There are four interrupt source registers for each UART:
ISR, LSR, STSInt, and SpclCharInt. Read the GlobalIRQ
Figure 16. Simplified Interrupt Structure
76
54
3
LSR
21
0
76
5
43
STSInt
21
0
00
GlobalIRQ
76
5
43
ISR
21
0
76 5 43
ISR
LOW-LEVEL INTERRUPTS
TOP-LEVEL
INTERRUPTS
21 0
76 5 43
ISR
21 0
76 5 43
ISR
21 0
76
5
43
SpclCharInt
21
0
IRQ3
IRQ
MODE1[7]:IRQSEL
IRQ1 IRQ0
IRQ2
8
4
[4]
POWER-UP
COMPLETED
[0]
相关PDF资料 |
PDF描述 |
|---|---|
| V24C12H150BL3 | CONVERTER MOD DC/DC 12V 150W |
| MAX3111EEWI+TG36 | IC UART SPI COMPAT 28-SOIC |
| MAX3100ETG+ | IC UART SPI/MICROWIRE 24-TQFN-EP |
| MAX3140EEI+T | IC UART W/RS485 28-QSOP |
| MAX3110EEWI+TG36 | IC UART SPI COMPAT 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX14830EVKIT# | 功能描述:界面开发工具 MAX14830 Eval Kit RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| MAX14830EVKIT+ | 制造商:Maxim Integrated Products 功能描述:QUAD UART EV-KIT WITH IO-LINK AND MULTIPROTOCOL - Boxed Product (Development Kits) |
| MAX1483C/D+ | 功能描述:RS-485接口IC low-power transceivers for RS-485 and RS-422 communication RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1483CPA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1483CPA+ | 功能描述:RS-422/RS-485 接口 IC Slew-Rate-Limited RS-485 Transceivers RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。