- 您现在的位置：买卖IC网 > PDF目录11817 > MAX14830ETM+T (Maxim Integrated Products)IC UART PDF资料下载
参数资料
| 型号： | MAX14830ETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 35/68页 |
| 文件大小： | 0K |
| 描述： | IC UART |
| 产品培训模块： | Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
40
Maxim Integrated
Quad Serial UART with 128-Word FIFOs
MAX14830
MODE2 Register
Bit 7: EchoSuprs
Set the EchoSuprs bit high so that the receiver (RX_) gates any data it receives when its transmitter is busy transmitting. In
half-duplex communication (like IrDA and RS-485) this allows blocking of the locally echoed data. The receiver can block
data for an extended time after the transmitter ceases transmission by programming a hold time in HDplxDelay[3:0] bits.
Bit 6: MultiDrop
Set the MultiDrop bit high to enable the 9-bit multidrop mode. If this bit is set, parity checking is not performed by the
receiver and parity generation is not done by the transmitter. The parity error bit, LSR[2], has a different meaning in
this case. The parity error bit represents the 9th bit (address/data indication) that is received with each 9-bit character.
Bit 5: Loopback
Set the Loopback bit high to enable internal local loopback mode. This internally connects TX_ to RX_ and also RTS_ to CTS_.
In local loopback mode, the TX_ output and the RX_ input are disconnected from the internal transmitter and receiver. The
TX_ output is in three-state. The RTS_ output remains connected to the internal logic and reflects the logic state programmed
in LCR[7]. The CTS_ input is disconnected from RTS_ and the internal logic. CTS_ thus remains in a high-impedance state.
Bit 4: SpecialChr
The SpecialChr bit enables special character detection. The receiver can detect up to four special characters, as
selected in FlowCtrl[5:4] and defined in the XON1, XON2, XOFF1 and/or XOFF2 registers, possibly in combination with
GPIO_ inputs, enabled through FlowCtrl[2]: GPIAddr. When a special character is received it is put into the RxFIFO
and a special character detect interrupt ISR[1] is generated.
Special character detection can be used in addition to auto XON/XOFF flow control, if enabled through FlowCtrl[3]. In
this case XON/XOFF flow control is then limited to single character XON and XOFF and only two special characters
can then be defined (in XON2 and XOFF2).
Bit 3: RxEmtyInv
The RxEmtyInv bit inverts the meaning of the receiver empty interrupt: ISR[6]: RFifoEmptyInt. If RxEmtyInv is set low
(default state), the ISR[6] interrupt is generated when the last character residing in the Receive FIFO is read out of the
RHR, and the Receive FIFO becomes empty. If the RxEmtyInv is set high, the ISR[6] interrupt is generated when the
Receive FIFO is empty, and the UART receives at least one character.
Bit 2: RxTrigInv
The RxTrigInv bit inverts the meaning of the RxFIFO triggering. When set, an ISR[3]: RFifoTrigInt is generated when
the RxFIFO is emptied to the trigger level: FIFOTrgLvl[7:4]. If the RxTrgInv bit is low (default state), the ISR[3] interrupt
is generated when the RxFIFO fill level, which starts from a level below FIFOTrgLvl[7:4], is filled up to the trigger level
programmed into FIFOTrgLvl[7:4].
Bit 1: FIFORst
Set the FIFORst bit high to clear both the Receive and Transmit FIFOs of all data contents. After the FIFO reset, the
FIFORst bit must then be set back to 0 to continue normal operation.
ADDRESS:
0x0A
MODE:
R/W
BIT
7
6
5
4
3
2
1
0
NAME
EchoSuprs
MultiDrop
Loopback
SpecialChr
RxEmtyInv
RxTrigInv
FIFORst
RST
RESET
0
相关PDF资料 |
PDF描述 |
|---|---|
| V24C12H150BL3 | CONVERTER MOD DC/DC 12V 150W |
| MAX3111EEWI+TG36 | IC UART SPI COMPAT 28-SOIC |
| MAX3100ETG+ | IC UART SPI/MICROWIRE 24-TQFN-EP |
| MAX3140EEI+T | IC UART W/RS485 28-QSOP |
| MAX3110EEWI+TG36 | IC UART SPI COMPAT 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX14830EVKIT# | 功能描述:界面开发工具 MAX14830 Eval Kit RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| MAX14830EVKIT+ | 制造商:Maxim Integrated Products 功能描述:QUAD UART EV-KIT WITH IO-LINK AND MULTIPROTOCOL - Boxed Product (Development Kits) |
| MAX1483C/D+ | 功能描述:RS-485接口IC low-power transceivers for RS-485 and RS-422 communication RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1483CPA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1483CPA+ | 功能描述:RS-422/RS-485 接口 IC Slew-Rate-Limited RS-485 Transceivers RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。