- 您现在的位置：买卖IC网 > PDF目录1836 > MAX15061ATE+ (Maxim Integrated Products)IC BOOST CONV/CURR MON 16-TQFN PDF资料下载
参数资料
| 型号： | MAX15061ATE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC BOOST CONV/CURR MON 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 应用： | 电流/电源监控器 |
| 电流 - 电源： | 1.2mA |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（4x4） |
| 包装： | 管件 |
80V, 300mW Boost Converter and Current
Monitor for APD Bias Applications
The MAX15061 includes a versatile current monitor
intended for monitoring the APD, PIN, or varactor diode
DC current in fiber and other applications. The
MAX15061 features more than three decades of
dynamic current ranging from 500nA to 4mA and pro-
vides an output current accurately proportional to the
APD current at MOUT.
The MAX15061 also features a shutdown logic input to
disable the device and reduce its standby current to
2μA (max).
Fixed-Frequency PWM Controller
The heart of the MAX15061 current-mode PWM con-
troller is a BiCMOS multiple-input comparator that
simultaneously processes the output-error signal and
switch current signal. The main PWM comparator uses
direct summing, lacking a traditional error amplifier and
its associated phase shift. The direct summing configu-
ration approaches ideal cycle-by-cycle control over the
output voltage since there is no conventional error
amplifier in the feedback path.
The device operates in PWM mode using a fixed-fre-
quency, current-mode operation. The current-mode fre-
quency loop regulates the peak inductor current as a
function of the output error signal.
The current-mode PWM controller is intended for dis-
continuous conduction mode (DCM) operation. No
internal slope compensation is added to the current
signal.
Charge Pump
At low supply voltages (2.7V to 5.5V), internal charge-
pump circuitry and an external 10nF ceramic capacitor
connected between CP and CN double the available inter-
nal supply voltage to drive the internal switch efficiently.
In the 5.5V to 11V supply voltage range, the charge
pump is not required. In this configuration, disable the
charge pump by connecting CP to IN and leaving CN
unconnected.
Monitor Current Limit (RLIM)
The current limit of the current monitor is programmable
from 1mA to 5mA. Connect a resistor from RLIM to
ground to program the current-limit threshold up to 5mA.
The current monitor mirrors the current out of APD with
a 1:10 ratio, and the MOUT current can be converted to
a voltage signal by connecting a resistor from MOUT to
SGND.
The APD current-monitor range is from 500nA to 4mA,
and the MOUT current-mirror output accuracy is ±10%
from 500nA to 1mA of APD current and ±3.5% from
1mA to 4mA of APD current.
Clamping the Monitor
Output Voltage (CLAMP)
CLAMP provides a means for diode clamping the volt-
age at MOUT; thus, V MOUT is limited to (V CLAMP +
0.6V). CLAMP can be connected to either an external
supply or BIAS. CLAMP can be left unconnected if volt-
age clamping is not required.
Adjusting the Boost Converter
Output Voltage (FB/CNTRL)
The boost converter output voltage can be set by con-
necting FB to a resistor-divider from V OUT to ground.
The set-point feedback reference is the 1.245 (typ)
internal reference voltage when V CNTRL > 1.5V and is
equal to the CNTRL voltage when V CNTRL < 1.25V.
To change the converter output on the fly, apply a volt-
age lower than 1.25V (typ) to the CNTRL input and
adjust the CNTRL voltage, which is the reference input
of the error amplifier when V CNTRL < 1.25V (see the
Functional Diagram). This feature can be used to adjust
the APD voltage based on the APD mirror current,
which compensates for the APD avalanche gain varia-
tion with temperature and manufacturing process. As
shown in Figure 4, the voltage signal proportional to the
MOUT current is connected to the analog-to-digital
(ADC) input of the APD module, which then controls the
reference voltage of the boost converter error amplifier
through a digital-to-analog (DAC) block connected to
the CNTRL input. The BIAS voltage and, therefore, the
APD current, are controlled based on the MOUT mirror
current, forming a negative feedback loop.
Shutdown ( SHDN )
The MAX15061 features an active-low shutdown input
( SHDN ). Pull SHDN low to enter shutdown. During shut-
down, the supply current drops to 2 μA (30 μA from
BIAS) (max). However, the output remains connected to
the input through the inductor and the output diode,
holding the output voltage to one diode drop below
PWR when the MAX15061 shuts down. Connect SHDN
to IN for always-on operation.
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15066EWE+T | IC REG BUCK SYNC ADJ 4A 16WLP |
| MAX1507ETA+T | IC BATT CHARGER LI-ION 8-TDFN |
| MAX1508ZETA+T | IC BATT CHARGER LI-ION 8-TDFN |
| MAX15101EWL+T | IC REG LDO ADJ 1A 15WLP |
| MAX15102EWL+T | IC REG LDO ADJ 2A 15WLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15061ATE+ | 功能描述:直流/直流开关转换器 80V 300mW Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15061ATE+T | 功能描述:直流/直流开关转换器 80V 300mW Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15062AATA+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX15062AATA+T | 功能描述:直流/直流开关调节器 36V 300mA Synchronous RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX15062ATA+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。