- 您现在的位置：买卖IC网 > PDF目录1836 > MAX15061ATE+ (Maxim Integrated Products)IC BOOST CONV/CURR MON 16-TQFN PDF资料下载
参数资料
| 型号： | MAX15061ATE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC BOOST CONV/CURR MON 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 应用： | 电流/电源监控器 |
| 电流 - 电源： | 1.2mA |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（4x4） |
| 包装： | 管件 |
80V, 300mW Boost Converter and Current
Monitor for APD Bias Applications
Determining Monitor Current Limit
Calculate the value of the monitor current-limit resistor,
R LIM , for a given APD current limit, I LIMIT , using the fol-
lowing equation:
protection is less critical when MOUT is connected
directly to subsequent transimpedance amplifiers (linear
or logarithmic) that have low-impedance, near-ground-
referenced inputs. If a transimpedance amplfier is used
R LIM = 10 ×
1.245V
I LIMIT (mA)
on the low side of the photodiode, its voltage drop must
also be considered. Leakage from the clamping diode
is most often insignificant over nominal operating condi-
tions, but grows with temperature.
The R LIM resistor, R LIM , ranges from 12.45k Ω to 2.5 Ω
for APD currents from 1mA to 5mA.
Applications Information
Using APD or PIN Photodiodes
in Fiber Applications
When using the MAX15061 to monitor APD or PIN pho-
todiode currents in fiber applications, several issues
must be addressed. In applications where the photodi-
ode must be fully depleted, keep track of voltages bud-
geted for each component with respect to the available
supply voltage(s). The current monitors require as
much as 1.1V between BIAS and APD, which must be
considered part of the overall voltage budget.
Additional voltage margin can be created if a negative
supply is used in place of a ground connection, as long
as the overall voltage drop experienced by the
MAX15061 is less than or equal to 76V. For this type of
application, the MAX15061 is suggested so the output
can be referenced to “true” ground and not the negative
supply. The MAX15061’s output current can be refer-
enced as desired with either a resistor to ground or a
transimpedance amplifier. Take care to ensure that out-
put voltage excursions do not interfere with the required
margin between BIAS and MOUT. In many fiber applica-
tions, MOUT is connected directly to an ADC that oper-
ates from a supply voltage that is less than the voltage
at BIAS. Connecting the MAX15061’s clamping diode
output, CLAMP, to the ADC power supply helps avoid
damage to the ADC. Without this protection, voltages
can develop at MOUT that might destroy the ADC. This
To maintain low levels of wideband noise, lowpass filter-
ing the output signal is suggested in applications where
only DC measurements are required. Connect the filter
capacitor at MOUT. Determining the required filtering
components is straightforward, as the MAX15061
exhibits a very high output impedance of 890M Ω .
In some applications where pilot tones are used to identi-
fy specific fiber channels, higher bandwidths are desired
at MOUT to detect these tones. Consider the minimum
and maximum currents to be detected, then consult the
frequency response and noise typical operating curves.
If the minimum current is too small, insufficient bandwidth
could result, while too high a current could result in
excessive noise across the desired bandwidth.
Layout Considerations
Careful PCB layout is critical to achieve low switching
losses and clean and stable operation. Protect sensitive
analog grounds by using a star ground configuration.
Connect SGND and PGND together close to the device
at the return terminal of the output bypass capacitor.
Do not connect them together anywhere else. Keep all
PCB traces as short as possible to reduce stray capaci-
tance, trace resistance, and radiated noise. Ensure that
the feedback connection to FB is short and direct.
Route high-speed switching nodes away from the sen-
sitive analog areas. Use an internal PCB layer for SGND
as an EMI shield to keep radiated noise away from the
device, feedback dividers, and analog bypass capaci-
tors. Refer to the MAX15061 evaluation kit data sheet
for a layout example.
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15066EWE+T | IC REG BUCK SYNC ADJ 4A 16WLP |
| MAX1507ETA+T | IC BATT CHARGER LI-ION 8-TDFN |
| MAX1508ZETA+T | IC BATT CHARGER LI-ION 8-TDFN |
| MAX15101EWL+T | IC REG LDO ADJ 1A 15WLP |
| MAX15102EWL+T | IC REG LDO ADJ 2A 15WLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15061ATE+ | 功能描述:直流/直流开关转换器 80V 300mW Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15061ATE+T | 功能描述:直流/直流开关转换器 80V 300mW Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15062AATA+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX15062AATA+T | 功能描述:直流/直流开关调节器 36V 300mA Synchronous RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX15062ATA+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。