参数资料
型号: MAX1540AETJ+T
厂商: Maxim Integrated Products
文件页数: 27/49页
文件大小: 0K
描述: IC REG CTRLR DIVIDER PWM 32-TQFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
PWM 型: 电流模式
输出数: 2
频率 - 最大: 620kHz
占空比: 100%
电源电压: 5.5 V ~ 28 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 85°C
封装/外壳: 32-WFQFN 裸露焊盘
包装: 带卷 (TR)
Dual Step-Down Controllers with Saturation
Protection, Dynamic Output, and Linear Regulator
SATURATION
LIMIT
QUAD-LEVEL
DECODE
9R
V CC - 1.0V
LSAT
ILIM_
DH DRIVER
S
R
0.5V
6 μ A
VALLEY CURRENT
LIMIT
R
Q
CSP_
ZERO
CROSSING
CSN_
SKIP
Figure 5. MAX1540A/MAX1541 Current-Limit Functional Diagram
ment (Figure 1). If the magnitude of the current-sense
( LIR2 )
signal  is  above  the  valley  current-limit  threshold,  the
PWM controller is not allowed to initiate a new cycle
(Figures 3 and 5). The actual peak current is greater
than the valley current-limit threshold by an amount
equal to the inductor ripple current. Therefore, the exact
current-limit characteristic and maximum load capability
are a function of the current-sense resistance, inductor
value, and battery voltage. When combined with the
undervoltage protection circuit, this current-limit method
is effective in almost every circumstance. Figure 6
shows the valley current-limit threshold point.
I LIM(VAL) = I LOAD(MAX) 1-
I PEAK
I LOAD
I LIMIT
In forced-PWM mode, the MAX1540A/MAX1541 also
implement a negative current limit to prevent excessive
0
TIME
reverse inductor currents when V OUT is sinking current.
The negative current-limit threshold is set to approxi-
mately 120% of the positive current limit and tracks the
positive current limit when ILIM is adjusted.
The current-limit threshold is adjusted with an external
resistor-divider at ILIM_. A 2μA to 20μA divider current
is recommended for accuracy and noise immunity. The
current-limit threshold adjustment range is from 25mV
to 200mV. In the adjustable mode, the current-limit
threshold voltage is precisely 1/10th the voltage seen at
ILIM_. The threshold defaults to 50mV when ILIM_ is
Figure 6. Valley Current-Limit Threshold Point
connected to V CC . The logic threshold for switchover to
the 50mV default value is approximately V CC - 1V.
Carefully observe the PC board layout guidelines to
ensure that noise and DC errors do not corrupt the dif-
ferential current-sense signals seen by CSP_ and
CSN_. Place the IC close to the sense resistor with
short, direct traces, making a Kelvin-sense connection
to the current-sense resistor.
______________________________________________________________________________________
27
相关PDF资料
PDF描述
B43088A4336M 33UF 350V 16X20 SINGLE END
MAX1637EEE+T IC REG CTRLR BUCK PWM CM 16-QSOP
GSM18DTMI-S189 CONN EDGECARD 36POS R/A .156 SLD
CAT1021LI-42-G IC SUPERVISR CPU 2K EEPROM 8PDIP
CAT1021LI-45-G IC SUPERVISR CPU 2K EEPROM 8PDIP
相关代理商/技术参数
参数描述
MAX1540ETJ 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX1540ETJ+ 功能描述:DC/DC 开关控制器 Dual Step-Down Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX1540ETJ+T 功能描述:DC/DC 开关控制器 Dual Step-Down Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX1540ETJ-T 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX1540EVKIT 功能描述:DC/DC 开关控制器 Evaluation Kit for the MAX1540 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK