- 您现在的位置：买卖IC网 > PDF目录15139 > MAX1540AETJ+T (Maxim Integrated Products)IC REG CTRLR DIVIDER PWM 32-TQFN PDF资料下载
参数资料
| 型号： | MAX1540AETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 42/49页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR DIVIDER PWM 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 620kHz |
| 占空比： | 100% |
| 电源电压： | 5.5 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 是 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页第45页第46页第47页第48页第49页
Dual Step-Down Controllers with Saturation
Protection, Dynamic Output, and Linear Regulator
V DDQ
V CC
V IN
SKIP
DH1
C IN
V TT = DDQ
10nF
10k Ω
10k Ω
LX1
REFIN1
DL1
MAX1541 GND
L
R SENSE
C OUT
V
2
CSP1
OD
CSN1
Figure 16. Active Bus Termination
GATE
FBLANK
OUT1
FB1
V DDQ = DDR MEMORY SUPPLY VOLTAGE
V TT = TERMINATION SUPPLY VOLTAGE
Voltage Positioning
In applications where fast load transients occur, the out-
put voltage changes instantly by ESR COUT x Δ I LOAD .
Voltage positioning allows the use of fewer output
PC board traces is a difficult task that must be
approached in terms of fractions of centimeters,
where a single milliohm of excess trace resistance
causes a measurable efficiency penalty.
capacitors for such applications, and maximizes the out-
put voltage AC and DC tolerance window in tight-toler-
ance applications.
Figure 17 shows the connection of OUT_ and FB_ in
voltage-positioned and nonvoltage-positioned circuits.
In nonvoltage-positioned circuits, the MAX1540A/
MAX1541 regulate at the output capacitor. In voltage-
positioned circuits, the MAX1540A/MAX1541 regulate
on the inductor side of the current-sense resistor.
V OUT_ is reduced to:
V OUT(VPS) = V OUT(NO LOAD) - R SENSE x I LOAD
?
?
?
Minimize current-sensing errors by connecting
CSP_ and CSN_ directly across the current-sense
resistor (R SENSE_ ).
When trade-offs in trace lengths must be made, it is
preferable to allow the inductor charging path to be
made longer than the discharge path. For example,
it is better to allow some extra distance between the
input capacitors and the high-side MOSFET than to
allow distance between the inductor and the low-
side MOSFET or between the inductor and the out-
put filter capacitor.
Route high-speed switching nodes (BST_, LX_,
Figure 18 shows the voltage-positioning transient
response.
PC Board Layout Guidelines
Careful PC board layout is critical to achieving low
switching losses and clean, stable operation. The
switching power stage requires particular attention
(Figure 19). If possible, mount all the power compo-
nents on the top side of the board, with their ground ter-
minals flush against one another. Follow these
guidelines for good PC board layout:
? Keep the high-current paths short, especially at the
ground terminals. This practice is essential for sta-
ble, jitter-free operation.
DH_, and DL_) away from sensitive analog areas
(REF, FB_, CSP_, CSN_).
Layout Procedure
1) Place the power components first, with ground ter-
minals adjacent (N L _ source, C IN , C OUT _, and D L _
anode). If possible, make all these connections on
the top layer with wide, copper-filled areas.
2) Mount the controller IC adjacent to the low-side
MOSFET, preferably on the back side opposite N L _
and N H _ in order to keep LX_, GND, DH_, and the
DL_ gate-drive lines short and wide. The DL_ and
DH_ gate traces must be short and wide (50 mils to
100 mils wide if the MOSFET is 1in from the con-
?
Keep the power traces and load connections short.
This practice is essential for high efficiency. Using
thick copper PC boards (2oz vs. 1oz) can enhance
full-load efficiency by 1% or more. Correctly routing
troller IC) to keep the driver impedance low and for
proper adaptive dead-time sensing.
42
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| B43088A4336M | 33UF 350V 16X20 SINGLE END |
| MAX1637EEE+T | IC REG CTRLR BUCK PWM CM 16-QSOP |
| GSM18DTMI-S189 | CONN EDGECARD 36POS R/A .156 SLD |
| CAT1021LI-42-G | IC SUPERVISR CPU 2K EEPROM 8PDIP |
| CAT1021LI-45-G | IC SUPERVISR CPU 2K EEPROM 8PDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1540ETJ | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1540ETJ+ | 功能描述:DC/DC 开关控制器 Dual Step-Down Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1540ETJ+T | 功能描述:DC/DC 开关控制器 Dual Step-Down Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1540ETJ-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1540EVKIT | 功能描述:DC/DC 开关控制器 Evaluation Kit for the MAX1540 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。