- 您现在的位置：买卖IC网 > PDF目录16795 > MAX16066ETL+ (Maxim Integrated Products)IC SYSTEM MANAGER 8CH 40-TQFN PDF资料下载
参数资料
| 型号： | MAX16066ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/62页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MANAGER 8CH 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | 电源监控器，序列发生器 |
| 电源电压： | 2.8 V ~ 14 V |
| 电流 - 电源： | 4.5mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
12-Channel/8-Channel, Flash-Configurable System
Managers with Nonvolatile Fault Registers
are MON1/MON2, MON3/MON4, MON5/MON6, MON7/
MON8, MON9/MON10, MON11/MON12 with the first
input always being at a higher voltage than the second.
Use differential voltage sensing to eliminate voltage off-
sets or measure supply current. See Figure 4. In differ-
ential mode, the odd-numbered MON_ input measures
the absolute voltage with respect to GND while the result
of the even input is the difference between the odd and
even inputs. See Figure 4 for the typical differential mea-
surement circuit.
Internal Current-Sense Amplifier
The current-sense inputs, CSP/CSM, and a current-
sense amplifier facilitate power monitoring (see Figure
5). The voltage on CSP relative to GND is also monitored
by the ADC when the current-sense amplifier is enabled
with r47h[0]. The conversion results are located in regis-
ters r19h and r1Ah (see Table 10). There are two select-
able voltage ranges for CSP set by r47h[1], see Table
8. Although the voltage can be monitored over SMBus
or JTAG, this voltage has no threshold comparators and
cannot trigger any faults. Regarding the current-sense
amplifier, there are four selectable ranges and the ADC
output for a current-sense conversion is:
X ADC = (V SENSE x A V )/1.4V x (2 8 - 1)
where X ADC is the 8-bit decimal ADC result in register
r18h, V SENSE is V CSP - V CSM, and A V is the current-
sense voltage gain set by r47h[3:2].
In addition, there are two programmable current-sense
trip thresholds: primary overcurrent and secondary over-
current. For fast fault detection, the primary overcurrent
threshold is implemented with an analog comparator
connected to the internal OVERC signal. The OVERC
signal can be output on one of the GPIO_s. See the
General-Purpose Inputs/Outputs section for configur-
ing the GPIO_ to output the OVERC signal. The primary
threshold is set by:
I TH = V CSTH /R SENSE
where I TH is the current threshold to be set, V CSTH is the
threshold set by r47h[3:2], and R SENSE is the value of
the sense resistor. See Table 8 for a description of r47h.
OVERC depends only on the primary overcurrent thresh-
old. The secondary overcurrent threshold is implement-
ed through ADC conversions and digital comparison set
by r6Ch. The secondary overcurrent threshold includes
programmable time delay options located in r73h[6:5].
Primary and secondary current-sense faults are enabled/
disabled through r47h[0].
General-Purpose Inputs/Outputs
GPIO1 – GPIO8 are programmable general-purpose
inputs/outputs. GPIO1–GPIO8 are configurable as a
manual reset input, a watchdog timer input and output,
logic inputs/outputs, fault-dependent outputs. When pro-
grammed as outputs, GPIO_s are open drain or push-
pull. See Tables 12 and 13 for more detailed information
on configuring GPIO1 – GPIO8.
POWER
R S
I LOAD
SUPPLY
V MON
MON ODD
MON EVEN
R SENSE
CSP
CSM
-
+
*A V
TO ADC MUX
MAX16065
MAX16066
LOAD
MAX16065
POWER
SUPPLY
MON ODD
LOAD
MON EVEN
OVERC
-
+
+
-
*V CSTH
*ADJUSTABLE BY r47h[3:2]
Figure 4. Differential Measurement Connections
Figure 5. Current-Sense Amplifier
18
_____________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| H3BBS-1006M | IDC CABLE - HSR10S/AE10M/HSR10S |
| MAX16067ETJ+ | IC SYSTEM MANAGER 6CH 32-TQFN |
| RCM06DTKT-S288 | CONN EDGECARD 12POS .156 EXTEND |
| H3AAH-1606G | IDC CABLE - HSC16H/AE16G/HSC16H |
| V300C12E150BF | CONVERTER MOD DC/DC 12V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16066ETL+ | 功能描述:监控电路 8Ch Power Supply Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16066ETL+T | 功能描述:监控电路 8Ch Power Supply Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16067ETJ+ | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16067ETJ+T | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16067EVKIT+ | 功能描述:监控电路 6-Channel System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。