- 您现在的位置：买卖IC网 > PDF目录16795 > MAX16067ETJ+ (Maxim Integrated Products)IC SYSTEM MANAGER 6CH 32-TQFN PDF资料下载
参数资料
| 型号： | MAX16067ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/48页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MANAGER 6CH 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 应用： | 电源监控器，序列发生器 |
| 电源电压： | 2.8 V ~ 14 V |
| 电流 - 电源： | 2.8mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
6-Channel, Flash-Configurable System Manager
with Nonvolatile Fault Registers
ALERT
GPIO1 is configurable as the SMBus alert signal, ALERT .
ALERT asserts when any fault condition occurs. When the
SMBus host sends the ARA (Alert Response Address),
the MAX16067 responds with its slave address and
deasserts ALERT . ALERT is an open-drain output.
Set the ARAEN bit in r40h[4] to ‘1’ to disable the ARA
feature. Under these conditions, the device does not
respond to an ARA on the SMBus line.
FAULT
GPIO2 is configurable as a dedicated fault output,
FAULT. FAULT asserts when an overvoltage or under-
voltage condition occurs on the selected inputs. FAULT
dependencies are set using registers r36h and r37h
(see Table 13). When FAULT depends on more than one
MON_, the fault output asserts when one or more MON_
exceeds a programmed threshold voltage. FAULT acts
independently of the critical fault system, described in
the Critical Faults section. Use r37h[7] to set the polarity
of FAULT.
Manual Reset ( MR )
GPIO3 is configurable to act as an active-low manual reset
input, MR . Drive MR low to assert RESET. RESET remains
asserted for the selected reset timeout period after MR
transitions from low to high. When connecting MR to a push-
button, use a pullup resistor. See the Reset Output section
for more information on selecting a reset timeout period.
Table 13. FAULT Dependencies
Watchdog Input (WDI) and Output ( WDO )
GPIO4 and GPIO5 are configurable as the watchdog
timer input (WDI) and output, WDO , respectively. See
Table 23 for configuration details. WDO is an open-drain,
active-low output. See the Watchdog Timer section for
more information about the operation of the watchdog
timer.
External Fault ( EXTFAULT )
GPIO6 is configurable as the external fault input/output,
EXTFAULT . EXTFAULT asserts if any monitored volt-
age exceeds an overvoltage or undervoltage threshold.
EXTFAULT also asserts if a power-up or power-down
sequencing fault occurs. This signal can be used to
cascade multiple MAX16067s.
Pull EXTFAULT low externally to force the sequencer to
enter a fault state. Under these conditions, all outputs
deassert.
Two configuration bits determine the behavior of the
MAX16067 when EXTFAULT is pulled low by an exter-
nal device. Register bit r72h[5], if set to a ‘1’, causes
the sequencer state machine to enter the fault state,
deasserting all the outputs when EXTFAULT is pulled
low. When this happens, the flag bit r1Ch[6] is set to
indicate the cause of the fault. If register bit r6Dh[2] is
set in addition to r72h[5], EXTFAULT going low triggers
a nonvolatile fault log operation.
REGISTER
ADDRESS
36h
37h
FLASH
ADDRESS
236h
237h
BIT RANGE
[0]
[1]
[2]
[3]
[4]
[5]
[7:6]
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
DESCRIPTION
FAULT depends on MON1 undervoltage threshold
FAULT depends on MON2 undervoltage threshold
FAULT depends on MON3 undervoltage threshold
FAULT depends on MON4 undervoltage threshold
FAULT depends on MON5 undervoltage threshold
FAULT depends on MON6 undervoltage threshold
Not used
FAULT depends on MON1 overvoltage threshold
FAULT depends on MON2 overvoltage threshold
FAULT depends on MON3 overvoltage threshold
FAULT depends on MON4 overvoltage threshold
FAULT depends on MON5 overvoltage threshold
FAULT depends on MON6 overvoltage threshold
Not used
0 = FAULT is an active-low digital output
1 = FAULT is an active-high digital output
18
_____________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| RCM06DTKT-S288 | CONN EDGECARD 12POS .156 EXTEND |
| H3AAH-1606G | IDC CABLE - HSC16H/AE16G/HSC16H |
| V300C12E150BF | CONVERTER MOD DC/DC 12V 150W |
| H3CCS-1606G | IDC CABLE - HKC16S/AE16G/HKC16S |
| H1DXS-1036G | IDC CABLE - HKR10S/AE10G/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16067ETJ+ | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16067ETJ+T | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16067EVKIT+ | 功能描述:监控电路 6-Channel System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16068ETI+ | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16068ETI+T | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。