- 您现在的位置：买卖IC网 > PDF目录16795 > MAX16070ETL+ (Maxim Integrated Products)IC SYSTEM MANAGER 12CH 40-TQFN PDF资料下载
参数资料
| 型号： | MAX16070ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 30/52页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MANAGER 12CH 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | 电源监控器 |
| 电源电压： | 2.8 V ~ 14 V |
| 电流 - 电源： | 4.5mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
12-Channel/8-Channel, Flash-Configurable System
Managers with Nonvolatile Fault Registers
Independent Watchdog Timer Operation
When r73h[4] is ‘1’ the watchdog timer operates in
the independent mode. In the independent mode, the
watchdog timer operates as if it were a separate device.
The watchdog timer is activated immediately upon V CC
exceeding UVLO and once the boot-up sequence is fin-
ished. When RESET is asserted, the watchdog timer and
WDO are not affected.
There will be a startup delay if r76h[6:4] is set to a value
different than ‘000.’ If r76h[6:4] is set to ‘000,’ there will
not be a startup delay. See Table 17 for delay times.
In independent mode, if the Watchdog Reset Output
Enable bit r76h[7] is set to ‘1,’ when the watchdog timer
expires, WDO asserts then RESET asserts. WDO will
then deassert. WDO will be low for approximately 1 F s.
If the Watchdog Reset Output Enable bit (r76h[7]) is set
to ‘0,’ when the WDT expires, WDO asserts but RESET
is not affected.
User-Defined Register
Register r8Ah provides storage space for a user-defined
configuration or firmware version number. Note that this
register controls the contents of the JTAG USERCODE
register bits 7:0. The user-defined register is stored at
r28Ah in the flash memory.
Memory Lock Bits
Register r8Ch contains the lock bits for the configuration
registers, configuration flash, user flash, and fault regis-
ter lock. See Table 18 for details.
Table 18. Memory Lock Bits
SMBus-Compatible Interface
The MAX16070/MAX16071 feature an SMBus-
compatible, 2-wire serial interface consisting of a serial-
data line (SDA) and a serial-clock line (SCL). SDA and
SCL facilitate bidirectional communication between the
MAX16070/MAX16071 and the master device at clock
rates up to 400kHz. Figure 1 shows the 2-wire interface
timing diagram. The MAX16070/MAX16071 are transmit/
receive slave-only devices, relying upon a master device
to generate a clock signal. The master device (typically
a microcontroller) initiates a data transfer on the bus and
generates SCL to permit that transfer.
A master device communicates to the MAX16070/
MAX16071 by transmitting the proper address followed
by a command and/or data words. The slave address
input, A0, is capable of detecting four different states,
allowing multiple identical devices to share the same
serial bus. The slave address is described further in
the Slave Address section. Each transmit sequence is
framed by a START (S) or REPEATED START (SR) con-
dition and a STOP (P) condition. Each word transmitted
over the bus is 8 bits long and is always followed by an
acknowledge pulse. SCL is a logic input, while SDA is
an open-drain input/output. SCL and SDA both require
external pullup resistors to generate the logic-high volt-
age. Use 4.7k I for most applications.
REGISTER
ADDRESS
FLASH ADDRESS
BIT RANGE
DESCRIPTION
Configuration register lock
0
1
1 = Locked
0 = Unlocked
Flash fault register lock
1 = Locked
8Ch
28Ch
2
3
0 = Unlocked
Flash configuration lock
1 = Locked
0 = Unlocked
User flash lock
1 = Locked
0 = Unlocked
30
_____________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| V300C12E150BF3 | CONVERTER MOD DC/DC 12V 150W |
| GBE05DHHT | CONN EDGECARD 10POS 1MM DIP SLD |
| H2MXS-1018M | DIP CABLE - HDM10S/AE10M/X |
| MAX16066ETL+ | IC SYSTEM MANAGER 8CH 40-TQFN |
| H3BBS-1006M | IDC CABLE - HSR10S/AE10M/HSR10S |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16070ETL+ | 功能描述:电流和电力监控器、调节器 12Ch System Monitor w/NV Fault Registers RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX16070ETL+T | 功能描述:电流和电力监控器、调节器 12Ch System Monitor w/NV Fault Registers RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX16071ETL+ | 功能描述:电流和电力监控器、调节器 8Ch System Monitor w/NV Fault Registers RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX16071ETL+T | 功能描述:电流和电力监控器、调节器 8Ch System Monitor w/NV Fault Registers RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX16072RS15D0+T | 功能描述:监控电路 uP Supervisor 1.58V Trip RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。