- 您现在的位置：买卖IC网 > PDF目录20674 > MAX1632AEAI+ (Maxim Integrated)IC REG TRPL BCK/LINEAR 28-SSOP PDF资料下载
参数资料
| 型号： | MAX1632AEAI+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 15/29页 |
| 文件大小： | 0K |
| 描述： | IC REG TRPL BCK/LINEAR 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 拓扑： | 降压（降压）同步（2），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 200kHz ~ 300kHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 12V，120mA |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 是 |
| 电源电压： | 4.2 V ~ 30 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Multi-Output, Low-Noise Power-Supply
Controllers for Notebook Computers
Shutdown Mode
Holding SHDN low puts the IC into its 4μA shutdown
mode. SHDN is logic input with a threshold of about 1V
(the V TH of an internal n-channel MOSFET). For auto-
matic startup, bypass SHDN to GND with a 0.01μF
capacitor and connect it to V+ through a 220k Ω resistor.
Power-Up Sequencing
and ON/ OFF Controls
Startup is controlled by RUN/ON3 and TIME/ON5 in
conjunction with SEQ. With SEQ tied to REF, the two
control inputs act as separate ON/ OFF controls for
each supply. With SEQ tied to VL or GND, RUN/ON3
becomes the master ON/ OFF control input and
TIME/ON5 becomes a timing pin, with the delay
between the two supplies determined by an external
capacitor. The delay is approximately 800μs/nF. The
+3.3V supply powers up first if SEQ is tied to VL, and
the +5V supply is first if SEQ is tied to GND. When driv-
ing TIME/ON5 as a control input with external logic,
always place a resistor (>1k Ω ) in series with the input.
This prevents possible crowbar current due to the inter-
nal discharge pulldown transistor, which turns on in
standby mode and momentarily at the first power-up or
in shutdown mode.
RESET Power-Good Voltage Monitor
The power-good monitor generates a system RESET sig-
nal. At first power-up, RESET is held low until both the
3.3V and 5V SMPS outputs are in regulation. At this point,
an internal timer begins counting oscillator pulses, and
RESET continues to be held low until 32,000 cycles have
elapsed. After this timeout period (107ms at 300kHz or
160ms at 200kHz), RESET is actively pulled up to VL. If
SEQ is tied to REF (for separate ON3/ON5 controls), only
the 3.3V SMPS is monitored—the 5V SMPS is ignored.
Table 4. Operating Modes
Output Undervoltage Shutdown Protection
(MAX1630A/MAX1631A/MAX1632A)
The output undervoltage lockout circuit is similar to
foldback current limiting, but employs a timer rather
than a variable current limit. Each SMPS has an under-
voltage protection circuit that is activated 6144 clock
cycles after the SMPS is enabled. If either SMPS output
is under 70% of the nominal value, both SMPSs are
latched off and their outputs are clamped to ground by
the synchronous rectifier MOSFETs (see the Output
Overvoltage Protection section). They do not restart
until SHDN or RUN/ON3 is toggled, or until V+ power is
cycled below 1V. Note that undervoltage protection can
make prototype troubleshooting difficult, since you
have only 20ms or 30ms to figure out what might be
wrong with the circuit before both SMPSs are latched
off. In extreme cases, it may be useful to substitute the
MAX1633A/MAX1634A/MAX1635A into the prototype
breadboard until the prototype is working properly.
Output Overvoltage Protection
(MAX1630A/MAX1631A/MAX1632A)
Both SMPS outputs are monitored for overvoltage. If
either output is more than 7% above the nominal regu-
lation point, both low-side gate drivers (DL_) are
latched high until SHDN or RUN/ON3 is toggled, or until
V+ power is cycled below 1V. This action turns on the
synchronous rectifiers with 100% duty, in turn rapidly
discharging the output capacitors and forcing both
SMPS outputs to ground. The DL outputs are also kept
high whenever the corresponding SMPS is disabled,
and in shutdown if VL is sustained.
SHDN
Low
High
High
High
High
High
High
High
High
SEQ
X
Ref
Ref
Ref
Ref
GND
GND
VL
VL
RUN/ON3
X
Low
High
Low
High
Low
High
Low
High
TIME/ON5
X
Low
Low
High
High
Timing capacitor
Timing capacitor
Timing capacitor
Timing capacitor
MODE
Shutdown
Standby
Run
Run
Run
Standby
Run
Standby
Run
DESCRIPTION
All circuit blocks turned off. Supply current = 4μA.
Both SMPSs off. Supply current = 30μA.
3.3V SMPS enabled/5V off.
5V SMPS enabled/3.3V off.
Both SMPSs enabled.
Both SMPSs off. Supply current = 30μA.
Both SMPSs enabled. 5V enabled before 3.3V.
Both SMPSs off. Supply current = 30μA.
Both SMPSs enabled. 3.3V enabled before 5V.
X = Don’t care.
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| ISL97519AIUZEVALZ | EVAL BOARD FOR ISL97519AIUZ |
| EEM25DCMI | CONN EDGECARD 50POS .156 SQ WW |
| MAX4210CEUA+T | IC CURRENT MONITOR 1.5% 8MSOP |
| VI-J62-CX-F2 | CONVERTER MOD DC/DC 15V 75W |
| MAX1999EEI+ | IC REG QD BCK/LINEAR SYNC 28QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1632AEAI+ | 功能描述:DC/DC 开关控制器 Multi-Out Low-Noise Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1632AEAI+T | 功能描述:DC/DC 开关控制器 Multi-Out Low-Noise Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1632AEAI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1632CAI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1632CAI+ | 制造商:Maxim Integrated Products 功能描述:DC DC CNTRLR DUAL-OUT STEP DOWN 4.2V TO 30V 28SSOP - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。