- 您现在的位置：买卖IC网 > PDF目录20674 > MAX1632AEAI+ (Maxim Integrated)IC REG TRPL BCK/LINEAR 28-SSOP PDF资料下载
参数资料
| 型号： | MAX1632AEAI+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 16/29页 |
| 文件大小： | 0K |
| 描述： | IC REG TRPL BCK/LINEAR 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 拓扑： | 降压（降压）同步（2），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 200kHz ~ 300kHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 12V，120mA |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 是 |
| 电源电压： | 4.2 V ~ 30 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Multi-Output, Low-Noise Power-Supply
Controllers for Notebook Computers
Discharging the output capacitor through the main
inductor causes the output to momentarily go below
GND. Clamp this negative pulse with a back-biased 1A
Schottky diode across the output capacitor (Figure 1).
To ensure overvoltage protection on initial power-up,
connect signal diodes from both output voltages to VL
(cathodes to VL) to eliminate the VL power-up delay.
This circuitry protects the load from accidental overvolt-
age caused by a short-circuit across the high-side
power MOSFETs. This scheme relies on the presence
of a fuse, in series with the battery, which is blown by
the resulting crowbar current. Note that the overvoltage
circuitry will interfere with external keep-alive supplies
that hold up the outputs (such as lithium backup or hot-
swap power supplies); in such cases, the MAX1633A,
MAX1634A, or MAX1635A should be used.
Low-Noise Operation (PWM Mode)
PWM mode ( SKIP = high) minimizes RF and audio
interference in noise-sensitive applications (such as hi-
fi multimedia-equipped systems), cellular phones, RF
communicating computers, and electromagnetic pen-
entry systems. See the summary of operating modes in
Table 2. SKIP can be driven from an external logic
signal.
Interference due to switching noise is reduced in PWM
mode by ensuring a constant switching frequency, thus
concentrating the emissions at a known frequency out-
side the system audio or IF bands. Choose an oscillator
frequency for which switching frequency harmonics do
not overlap a sensitive frequency band. If necessary,
synchronize the oscillator to a tight-tolerance external
clock generator. To extend the output-voltage-regula-
tion range, constant operating frequency is not main-
tained under overload or dropout conditions (see the
Overload and Dropout Operation section . )
PWM mode ( SKIP = high) forces two changes upon the
PWM controllers. First, it disables the minimum-current
comparator, ensuring fixed-frequency operation.
Second, it changes the detection threshold for reverse-
current limit from 0mV to -100mV, allowing the inductor
current to reverse at light loads. This results in fixed-
frequency operation and continuous inductor-current
flow. This eliminates discontinuous-mode inductor ring-
ing and improves cross regulation of transformer-
coupled multiple-output supplies, particularly in circuits
that do not use additional secondary regulation through
SECFB or V DD .
In most applications, tie SKIP to GND to minimize qui-
escent supply current. VL supply current with SKIP high
is typically 20mA, depending on external MOSFET gate
capacitance and switching losses.
Internal Digital Soft-Start Circuit
Soft-start allows a gradual increase of the internal cur-
rent-limit level at startup to reduce input surge currents.
Both SMPSs contain internal digital soft-start circuits,
each controlled by a counter, a digital-to-analog con-
verter (DAC), and a current-limit comparator. In shut-
down or standby mode, the soft-start counter is reset to
zero. When an SMPS is enabled, its counter starts
counting oscillator pulses, and the DAC begins incre-
menting the comparison voltage applied to the current-
limit comparator. The DAC output increases from 0mV to
100mV in five equal steps as the count increases to 512
clocks. As a result, the main output capacitor charges
up relatively slowly. The exact time of the output rise
depends on output capacitance and load current, and
is typically 1ms with a 300kHz oscillator.
Dropout Operation
Dropout (low input-output differential operation) is
enhanced by stretching the clock pulse width to
increase the maximum duty factor. The algorithm fol-
lows: If the output voltage (V OUT ) drops out of regula-
tion without the current limit having been reached, the
SMPS skips an off-time period (extending the on-time).
At the end of the cycle, if the output is still out of regula-
tion, the SMPS skips another off-time period. This
action can continue until three off-time periods are
skipped, effectively dividing the clock frequency by as
much as four.
The typical PWM minimum off-time is 300ns, regardless
of the operating frequency. Lowering the operating fre-
quency raises the maximum duty factor above 98%.
Adjustable-Output Feedback
(Dual Mode FB)
Fixed, preset output voltages are selected when FB_ is
connected to ground. Adjusting the main output volt-
age with external resistors is simple for any of the
MAX1630A family ICs, through resistor-dividers con-
nected to FB3 and FB5 (Figure 2). Calculate the output
voltage with the following formula:
V OUT = V REF (1 + R1 / R2)
where V REF = 2.5V nominal.
The nominal output should be set approximately 1% or
2% high to make up for the MAX1630A’s -2% typical
load-regulation error. For example, if designing for a
3.0V output, use a resistor ratio that results in a nominal
output voltage of 3.05V. This slight offsetting gives the
best possible accuracy. Recommended normal values
for R2 range from 5k Ω to 100k Ω . To achieve a 2.5V
nominal output, connect FB_ directly to CSL_.
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ISL97519AIUZEVALZ | EVAL BOARD FOR ISL97519AIUZ |
| EEM25DCMI | CONN EDGECARD 50POS .156 SQ WW |
| MAX4210CEUA+T | IC CURRENT MONITOR 1.5% 8MSOP |
| VI-J62-CX-F2 | CONVERTER MOD DC/DC 15V 75W |
| MAX1999EEI+ | IC REG QD BCK/LINEAR SYNC 28QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1632AEAI+ | 功能描述:DC/DC 开关控制器 Multi-Out Low-Noise Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1632AEAI+T | 功能描述:DC/DC 开关控制器 Multi-Out Low-Noise Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1632AEAI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1632CAI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1632CAI+ | 制造商:Maxim Integrated Products 功能描述:DC DC CNTRLR DUAL-OUT STEP DOWN 4.2V TO 30V 28SSOP - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。