- 您现在的位置：买卖IC网 > PDF目录1838 > MAX1639ESE+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 16-SOIC PDF资料下载
参数资料
| 型号： | MAX1639ESE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/13页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.2MHz |
| 占空比： | 84% |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
High-Speed Step-Down Controller with
Synchronous Rectification for CPU Power
P D ( low side ) = I LOAD
x R DS ( ON ) x ? 1 ?
CC 1 =
C OUT x R ESR
10 k ?
2
?
?
V OUT ?
V IN ? ?
Resistor RC1 sets a zero that can be used to compen-
sate for the sampling pole generated by the switching
frequency. Set RC1 to the following:
Gate-charge losses are dissipated in the IC, and do not
heat the MOSFETs. Ensure that both MOSFETs are at a
safe junction temperature by calculating the temperature
rise according to package thermal-resistance specifica-
? 1 +
RC 1 =
? V OUT ?
?
? V IN ?
2 f OSC x CC 1
tions. The high-side MOSFET’s worst-case dissipation
occurs at the maximum output voltage and minimum
input voltage. For the low-side MOSFET, the worst case
is at the maximum input voltage when the output is short-
circuited (consider the duty factor to be 100%).
The CC1 pin’s output resistance is 10k ? .
Setting the Dominant Pole
and Canceling the Load and Output Filter Pole
Compensate the slow-voltage feedback loop by adding
a ceramic capacitor from the CC2 pin to AGND. This is
an integrator loop used to cancel out the DC load-
regulation error. Selection of capacitor CC2 sets the
dominant pole and a compensation zero. The zero is typ-
ically used to cancel the unwanted pole generated by the
load and output filter capacitor at the maximum load cur-
rent. Select CC2 to place the zero close to or slightly
lower than the frequency of the unwanted pole, as fol-
lows:
Calculating IC Power Dissipation
Power dissipation in the IC is dominated by average
gate-charge current into both MOSFETs. Average cur-
rent is approximately:
I DD = (Q G1 + Q G2 ) x f OSC
where I DD is the drive current, Q G is the total gate
charge for each MOSFET, and f OSC is the switching
frequency.
Power dissipation of the IC is:
P D = I CC x V CC + I DD x V DD
where I CC is the quiescent supply current of the IC.
Junction temperature for the IC is primarily a function of
the PC board layout, since most of the heat is removed
CC 2 =
1 mmho x C OUT
4
x
V OUT
I OUT ( MAX )
through the traces connected to the pins and the
ground and power planes. A 16-pin narrow SO on a
typical four-layer board with ground and power planes
The transconductance of the integrator amplifier at CC2
is 1mmho. The voltage swing at CC2 is internally
clamped around 2.4V to 3V minimum and 4V to V CC
maximum to improve transient response times. CC2
can source and sink up to 100μA.
Choosing the MOSFET Switches
The two high-current N-channel MOSFETs must be
logic-level types with guaranteed on-resistance specifi-
cations at V GS = 4.5V. Lower gate-threshold specs are
better (i.e., 2V max rather than 3V max). Gate charge
should be less than 200nC to minimize switching losses
and reduce power dissipation.
I 2 R losses are the greatest heat contributor to MOSFET
power dissipation and are distributed between the
high- and low-side MOSFETs according to duty factor,
as follows:
show equivalent junction-to-ambient thermal
impedance of ( θ JA ) about 80°C/W. Junction tempera-
ture of the die is approximately:
T J = P D x θ JA + T A
where T A is the ambient temperature.
Selecting the Rectifier Diode
The rectifier diode D1 is a clamp that catches the nega-
tive inductor swing during the 30ns typical dead time
between turning off the high-side MOSFET and turning
on the low-side MOSFET synchronous rectifier. D1 must
be a Schottky diode, to prevent the MOSFET body
diode from conducting. It is acceptable to omit D1 and
let the body diode clamp the negative inductor swing,
but efficiency will drop about 1%. Use a 1N5819 diode
for loads up to 3A, or a 1N5822 for loads up to 10A.
Adding the BST Supply Diode
P D ( high side ) = I LOAD
2
x R DS ( ON ) x
V OUT
V IN
and Capacitor
A signal diode, such as a 1N4148, works well for D2 in
most applications, although a low-leakage Schottky
diode provides slightly improved efficiency. Do not use
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1641EEE+ | IC SW-MODE CUR SOURCE ADJ 16QSOP |
| MAX1644EAE-T | IC REG BUCK SYNC ADJ 2A 16SSOP |
| MAX1651CSA | IC REG CTRLR BUCK PWM 8-SOIC |
| MAX1653EEE-T | IC REG CTRLR BUCK PWM CM 16-QSOP |
| MAX1659ESA+ | IC REG LDO 5V/ADJ .35A 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1639EVKIT | 功能描述:DC/DC 开关控制器 Evaluation Kit the MAX1639 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX163BCNG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX163BCNG+ | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX163BCWG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX163BCWG+ | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。