- 您现在的位置：买卖IC网 > PDF目录20712 > MAX16816ATJ+T (Maxim Integrated)IC LED DRIVR HIGH BRIGHT 32-TQFN PDF资料下载
参数资料
| 型号： | MAX16816ATJ+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 12/33页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR HIGH BRIGHT 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 拓扑： | PWM，SEPIC，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 125kHz ~ 500kHz |
| 电源电压： | 5.5 V ~ 76 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Programmable Switch-Mode LED Driver
with Analog-Controlled PWM Dimming
Pin Description
PIN
1, 24
2
3
4
5
6
7
8
9, 10, 11
12
13
14
15
16, 17
18
19
20
NAME
N.C.
UVEN
REG1
AGND
REF
DIM
RTSYNC
CLKOUT
I.C.
COMP
CS
FB
OV
SGND
DRV
DRI
SNS+
FUNCTION
No Connection. Not internally connected.
Undervoltage Lockout (UVLO) Threshold/Enable Input. UVEN is a dual-function adjustable UVLO threshold
input with an enable feature. Connect UVEN to V CC through a resistive voltage-divider to program the UVLO
threshold. Connect UVEN directly to V CC to use the 5.9V (max) default UVLO threshold. Apply a voltage
greater than 1.244V to UVEN to enable the device.
5V Regulator Output. REG1 is an internal low-dropout voltage regulator that generates a 5V (V CC > 6V)
output voltage and supplies power to internal circuitry. Bypass REG1 to AGND through a 1μF ceramic
capacitor.
Analog Ground. Use proper single-point ground design and decoupling to avoid ground impedance loop
errors.
Accurate 3V Buffered Reference Output. Connect REF to DIM through a resistive voltage-divider to apply a
DC voltage for analog-controlled dimming functionality. Leave REF unconnected if unused.
Dimming Control Input. Connect DIM to an external PWM signal for PWM dimming. For analog-controlled
dimming, connect DIM to REF through a resistive voltage-divider. The dimming frequency is 200Hz under
these conditions. Connect DIM to AGND to turn off the LEDs.
Sync Input/Output. The internal PWM clock is selectable through the RTOF EEPROM bit. Connect an
external resistor to RTSYNC and set the RTOF register to ‘0’ to select a clock frequency between 125kHz
and 500kHz. Set RTOF register to ‘0’ and connect RTSYNC to an external clock to synchronize the device
with external clock. Set RTOF register to ‘1’ to use the fixed 125kHz oscillator. Under these conditions,
RTSYNC is powered off and may be left in any state. See the Oscillator, Clock, and Synchronization section.
Clock Output. CLKOUT buffers the oscillator/clock. Connect CLKOUT to the SYNC input of another device
to operate the MAX16816 in a multichannel configuration. CLKOUT is a logic output.
Internally Connected. Must be connected to AGND.
Error-Amplifier Output. Connect the compensation network from COMP to FB for stable closed-loop control.
Use low-leakage ceramic capacitors in the feedback network.
Current-Sense Voltage Output. CS outputs a voltage proportional to the current sensed through the current-
sense amplifier. Connect CS through a passive network to FB as dictated by the chosen compensation
scheme.
Error-Amplifier Inverting Input
Overvoltage Protection Input. Connect OV to HI through a resistive voltage-divider to set the overvoltage
limit for the load. When the voltage at OV exceeds the 1.235V (typ) threshold, an overvoltage fault is
generated and the switching MOSFET turns off. The MOSFET is turned on again when the voltage at OV
drops below 1.17V (typ).
Switching Ground. SGND is the ground for non-analog and high-current gate-driver circuitry.
Gate-Driver Output. Connect DRV through a series resistor to the gate of an external n-channel MOSFET to
reduce EMI. DRV can sink 1A or source 0.5A.
Gate-Driver Supply Input. Connect DRI to REG2 to power the primary switching MOSFET driver.
Positive Peak Current-Sense Input. Connect SNS+ to the positive side of the switch current-sense resistor,
R SENSE .
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J3V-EW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-J3V-CX-F4 | CONVERTER MOD DC/DC 5.8V 75W |
| ECA18DCBD | CONN EDGECARD 36POS R/A .125 SLD |
| ECA18DCBH | CONN EDGECARD 36POS R/A .125 SLD |
| RBA10DTKI-S288 | CONN EDGECARD 20POS .125 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16816EVKIT+ | 功能描述:LED 照明开发工具 MAX16816 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX16818ATI+ | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16818ATI+T | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16818ETI+ | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16818ETI+T | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。