- 您现在的位置：买卖IC网 > PDF目录20712 > MAX16816ATJ+T (Maxim Integrated)IC LED DRIVR HIGH BRIGHT 32-TQFN PDF资料下载
参数资料
| 型号： | MAX16816ATJ+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 18/33页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR HIGH BRIGHT 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 拓扑： | PWM，SEPIC，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 125kHz ~ 500kHz |
| 电源电压： | 5.5 V ~ 76 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Programmable Switch-Mode LED Driver
with Analog-Controlled PWM Dimming
where V SENSE is the 200mV maximum differential volt-
age between SNS+ and SNS- and I PEAK is the peak
inductor current at full load and minimum input voltage.
When the voltage drop across R SENSE exceeds the
ILIM threshold, the MOSFET driver (DRV) terminates
the on-cycle and turns the switch off, reducing the cur-
rent through the inductor. The FET is turned back on at
the beginning of the next switching cycle.
When the voltage across R SENSE exceeds the 300mV
(typ) HICCUP threshold, the HIC comparator terminates
the on-cycle of the device, turning the switching MOS-
FET off. Following a startup delay of 8ms (typ), the
MAX16816 reinitiates soft-start. The device will continue
to operate in HICCUP mode until the overcurrent condi-
tion is removed.
A programmable built-in leading-edge blanking circuit
of the current-sense signal prevents these comparators
from prematurely terminating the on-cycle of the exter-
nal switching MOSFET (Q S ). Select a blanking time
from 75ns to 150ns by configuring the Blanking Time
register in the EEPROM. In some cases, the maximum
blanking time may not be adequate and an additional
RC filter may be required to prevent spurious turn-off.
Load Current Sense
The load sense resistor, R CS , monitors the current
through the LEDs. The internal floating current-sense
amplifier, CSA, measures the differential voltage across
R CS , and generates a voltage proportional to the load
current through R CS at CS. This voltage on CS is
referred to AGND. The closed-loop regulates the load
current to a value, I LED , given by the following equation:
I LED = V SS / R CS
where V SS is the binning adjustment voltage. Set the value
of V SS in the Binning Adjustment register in the EEPROM
between 100mV and 166mV. See the EEPROM and
Programming section for more information on adjusting
the binning voltage.
Slope Compensation
The amount of slope compensation required is largely
dependent on the down-slope of the inductor current
when the switching MOSFET, Q S , is off. The inductor
down-slope depends on the input-to-output voltage dif-
ferential of the converter, the inductor value, and the
switching frequency. For stability, the compensation
slope should be equal to or greater than half of the
inductor current down-slope multiplied by the current-
sense resistance (R SENSE ).
See the EEPROM and Programming section for more infor-
mation on the ESLP register.
Internal Voltage-Error Amplifier (EAMP)
The MAX16816 includes a built-in voltage amplifier,
with three-state output, which can be used to close the
feedback loop. The buffered output current-sense sig-
nal appears at CS, which is connected to the inverting
input, FB, of the error amplifier through resistor R 1 . The
noninverting input is connected to an internally trimmed
current reference.
The output of the error amplifier is controlled by the signal
applied to DIM. When DIM is high, the output of the ampli-
fier is connected to COMP. The amplifier output is open
when DIM is low. This enables the integrating capacitor to
hold the charge when the DIM signal has turned off the
gate drive. When DIM is high again, the voltage on the
compensation capacitors, C 1 and C 2 , forces the converter
into steady state almost instantaneously.
PWM Dimming
PWM dimming is achieved by driving DIM with either a
PWM signal or a DC signal. The PWM signal is con-
nected internally to the error amplifier, the dimming
MOSFET gate driver, and the switching MOSFET gate
driver. When the DIM signal is high, the dimming MOSFET
and the switching MOSFET drivers are enabled and the
output of the voltage-error amplifier is connected to
the external compensation network. Also, the buffered
current-sense signal is connected to CS. Preventing
discharge of the compensation capacitor when the
DIM signal is low allows the control loop to return the
LED current to its original value almost instantaneously.
When the DIM signal goes low, the output of the error
amplifier is disconnected from the compensation net-
work and the compensation capacitors, C 1 and C 2 ,
voltage is preserved. Choose low-leakage capacitors
for C 1 and C 2 . The drivers for the external dimming and
switching MOSFETs are disabled, and the converter
stops switching. The inductor energy is now transferred
to the output capacitors.
When the DIM signal goes high and the gate drivers
are enabled, the additional voltage on the output
capacitor may cause a current spike on the LED string.
A larger output capacitor will result in a smaller current
spike. If the overcurrent spike exceeds 30% of the pro-
grammed LED current, the dimming is turned off and
the MAX16816 reinitiates soft-start.
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J3V-EW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-J3V-CX-F4 | CONVERTER MOD DC/DC 5.8V 75W |
| ECA18DCBD | CONN EDGECARD 36POS R/A .125 SLD |
| ECA18DCBH | CONN EDGECARD 36POS R/A .125 SLD |
| RBA10DTKI-S288 | CONN EDGECARD 20POS .125 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16816EVKIT+ | 功能描述:LED 照明开发工具 MAX16816 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX16818ATI+ | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16818ATI+T | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16818ETI+ | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16818ETI+T | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。