- 您现在的位置：买卖IC网 > PDF目录5135 > MAX17004ETJ+T (Maxim Integrated Products)IC PS CTRLR FOR NOTEBOOKS 32TQFN PDF资料下载
参数资料
| 型号： | MAX17004ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 26/36页 |
| 文件大小： | 0K |
| 描述： | IC PS CTRLR FOR NOTEBOOKS 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 6 V ~ 26 V |
| 输出数： | 4 |
| 输出电压： | 3.3V，5V，2 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
High-Efficiency, Quad-Output, Main Power-
Supply Controllers for Notebook Computers
Ferrite cores are often the best choice, although pow-
dered iron is inexpensive and can work well at 200kHz.
The core must be large enough not to saturate at the
peak inductor current (I PEAK ):
instead of ground in order to reduce the necessary turns
ratio. In this case, subtract V OUT5 from the secondary
voltage (V SEC - V OUT5 ) in the transformer turns-ratio
equation above. The secondary diode in coupled-induc-
tor applications must withstand flyback voltages greater
I PEAK = I LOAD ( MAX ) +
Δ I INDUCTOR
2
than 60V. Common silicon rectifiers, such as the 1N4001,
are also prohibited because they are too slow. Fast sili-
con rectifiers such as the MURS120 are the only choice.
Transformer Design (for
MAX17003/MAX17004 Auxiliary Output)
A coupled inductor or transformer can be substituted
for the inductor in the 5V SMPS to create an auxiliary
output (Figure 1). The MAX17003/MAX17004 is particu-
larly well suited for such applications because the sec-
ondary feedback threshold automatically triggers DL5
even if the 5V output is lightly loaded.
The power requirements of the auxiliary supply must be
considered in the design of the main output. The trans-
former must be designed to deliver the required current
in both the primary and the secondary outputs with the
proper turns ratio and inductance. The power ratings of
the synchronous-rectifier MOSFETs and the current limit
in the MAX17003/MAX17004 must also be adjusted
accordingly. Extremes of low input-output differentials,
widely different output loading levels, and high turns
ratios can further complicate the design due to parasitic
transformer parameters such as interwinding capaci-
tance, secondary resistance, and leakage inductance.
Power from the main and secondary outputs is com-
bined to get an equivalent current referred to the main
output. Use this total current to determine the current
The flyback voltage across the rectifier is related to the
V IN - V OUT5 difference, according to the transformer
turns ratio:
V FLYBACK = V SEC + (V IN – V OUT5 ) x N
where N is the transformer turns ratio (secondary wind-
ings/primary windings), and V SEC is the maximum sec-
ondary DC output voltage. If the secondary winding is
returned to V OUT5 instead of ground, subtract V OUT5
from V FLYBACK in the equation above. The diode ’s
reverse breakdown voltage rating must also accommo-
date any ringing due to leakage inductance. The
diode’s current rating should be at least twice the DC
load current on the secondary output.
Transient Response
The inductor ripple current also impacts transient-
response performance, especially at low V IN - V OUT dif-
ferentials. Low inductor values allow the inductor
current to slew faster, replenishing charge removed
from the output filter capacitors by a sudden load step.
The total output voltage sag is the sum of the voltage
sag while the inductor is ramping up, and the voltage
sag before the next pulse can occur:
limit (see the Setting the Current Limit section):
I TOTAL = P TOTAL /V OUT5
where I TOTAL is the equivalent output current referred
to the main output, and P TOTAL is the sum of the output
power from both the main output and the secondary
V SAG =
L ( Δ I LOAD ( MAX ) ) 2
2 C OUT ( V IN x D MAX ? V OUT
Δ I LOAD ( MAX ) ( T ? Δ T )
)
+
output:
C OUT
N =
V SEC + V FWD
V OUT 5 + V RECT + V SENSE
where D MAX is maximum duty factor (see the Electrical
Characteristics), T is the switching period (1/f OSC ), and
Δ T equals V OUT /V IN x T when in PWM mode, or L x 0.2 x
≈ ( Δ I LOAD ( MAX ) ) 2 L
where N is the transformer turns ratio, V SEC is the mini-
mum required rectified secondary voltage, V FWD is the
forward drop across the secondary rectifier, V OUT5(MIN)
is the minimum value of the main output voltage, and
V RECT is the on-state voltage drop across the synchro-
nous-rectifier MOSFET. The transformer secondary
return is often connected to the main output voltage
I MAX /(V IN - V OUT ) when in skip mode. The amount of
overshoot during a full-load to no-load transient due to
stored inductor energy can be calculated as:
V SOAR
2 C OUT V OUT
26
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| 63MXG15000MEFCSN35X50 | CAP ALUM 15000UF 63V 20% SNAP-IN |
| ACB24DHFD | CONN EDGECARD 48POS .050 SMD |
| 400VXG680MEFCSN35X50 | CAP ALUM 680UF 400V 20% SNAP-IN |
| 450VXH560MEFCSN35X45 | CAP ALUM 560UF 450V 20% SNAP-IN |
| 400MXH560MEFCSN35X35 | CAP ALUM 560UF 400V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17005AETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005AETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005BETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005BETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005DEVKIT+ | 功能描述:电源管理IC开发工具 Programmers, Development Systems RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。