- 您现在的位置：买卖IC网 > PDF目录5135 > MAX17004ETJ+T (Maxim Integrated Products)IC PS CTRLR FOR NOTEBOOKS 32TQFN PDF资料下载
参数资料
| 型号： | MAX17004ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 29/36页 |
| 文件大小： | 0K |
| 描述： | IC PS CTRLR FOR NOTEBOOKS 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 6 V ~ 26 V |
| 输出数： | 4 |
| 输出电压： | 3.3V，5V，2 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页
High-Efficiency, Quad-Output, Main Power-
Supply Controllers for Notebook Computers
f ESR ≤ OSC
The actual capacitance value required relates to the
physical size needed to achieve low ESR, as well as to
the chemistry of the capacitor technology. Thus, the
capacitor is usually selected by ESR and voltage rating
rather than by capacitance value (this is true of tanta-
lums, OS-CONs, polymers, and other electrolytics).
When using low-capacity filter capacitors, such as
ceramic capacitors, size is usually determined by the
capacity needed to prevent V SAG and V SOAR from
causing problems during load transients. Generally,
once enough capacitance is added to meet the over-
shoot requirement, undershoot at the rising load edge
is no longer a problem (see the V SAG and V SOAR equa-
tions in the Transient Response section). However, low-
capacity filter capacitors typically have high ESR zeros
that may affect the overall stability (see the Output-
Capacitor Stability Considerations section).
Output-Capacitor Stability Considerations
Stability is determined by the value of the ESR zero rel-
ative to the switching frequency. The boundary of insta-
bility is given by the following equation:
f
π
where:
For low-input voltage applications where the duty cycle
exceeds 50% (V OUT /V IN ≥ 50%), the output ripple voltage
should not be greater than twice the internal slope-
compensation voltage:
V RIPPLE ≤ 0.02 x V OUT
where V RIPPLE equals Δ I INDUCTOR x R ESR . The worst-
case ESR limit occurs when V IN = 2 x V OUT , so the
above equation may be simplified to provide the follow-
ing boundary condition:
R ESR ≤ 0.04 x L x f SW
Do not put high-value ceramic capacitors directly
across the feedback sense point without taking precau-
tions to ensure stability. Large ceramic capacitors can
have a high-ESR zero frequency and cause erratic,
unstable operation. However, it is easy to add enough
series resistance by placing the capacitors a couple of
inches downstream from the feedback sense point,
which should be as close as possible to the inductor.
Unstable operation manifests itself in two related but
distinctly different ways: short/long pulses and cycle
skipping resulting in lower frequency operation.
Instability occurs due to noise on the output or because
the ESR is so low that there is not enough voltage ramp
in the output voltage signal. This “fools” the error com-
parator into triggering too early or into skipping a cycle.
f ESR =
1
2 π R ESR C OUT
Cycle skipping is more annoying than harmful, resulting
in nothing worse than increased output ripple.
However, it can indicate the possible presence of loop
For a typical 300kHz application, the ESR zero frequen-
cy must be well below 95kHz, preferably below 50kHz.
Tantalum and OS-CON capacitors in widespread use
at the time of publication have typical ESR zero fre-
quencies of 25kHz. In the design example used for
inductor selection, the ESR needed to support 25mV P-P
ripple is 25mV/1.5A = 16.7m Ω . One 220μF/4V Sanyo
polymer (TPE) capacitor provides 15m Ω (max) ESR.
This results in a zero at 48kHz, well within the bounds
of stability.
instability due to insufficient ESR. Loop instability can
result in oscillations at the output after line or load
steps. Such perturbations are usually damped, but can
cause the output voltage to rise above or fall below the
tolerance limits.
The easiest method for checking stability is to apply a
very fast zero-to-max load transient and carefully
observe the output-voltage-ripple envelope for over-
shoot and ringing. It may help to simultaneously moni-
tor the inductor current with an AC current probe. Do
not allow more than three cycles of ringing after the ini-
tial step-response under/overshoot.
______________________________________________________________________________________
29
相关PDF资料 |
PDF描述 |
|---|---|
| 63MXG15000MEFCSN35X50 | CAP ALUM 15000UF 63V 20% SNAP-IN |
| ACB24DHFD | CONN EDGECARD 48POS .050 SMD |
| 400VXG680MEFCSN35X50 | CAP ALUM 680UF 400V 20% SNAP-IN |
| 450VXH560MEFCSN35X45 | CAP ALUM 560UF 450V 20% SNAP-IN |
| 400MXH560MEFCSN35X35 | CAP ALUM 560UF 400V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17005AETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005AETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005BETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005BETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005DEVKIT+ | 功能描述:电源管理IC开发工具 Programmers, Development Systems RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。