- 您现在的位置：买卖IC网 > PDF目录15533 > MAX17006BETP+T (Maxim Integrated Products)IC BATT CHARGER 1.2MHZ 20-TQFN PDF资料下载
参数资料
| 型号： | MAX17006BETP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/22页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER 1.2MHZ 20-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 多化学 |
| 电源电压： | 8 V ~ 26 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
1.2MHz, Low-Cost,
High-Performance Chargers
The PWM filter accepts the digital signal with a frequency
from 128Hz to 500kHz. Zero duty cycle shuts down the
MAX17005B/MAX17006B/MAX17015B, and 99.5% duty
cycle corresponds to full scale (60mV) across CSIP
and CSIN.
Choose a current-sense resistor (RS2) to have a suffi-
cient power-dissipation rating to handle the full-charge
current. The current-sense voltage can be reduced to
minimize the power-dissipation period. However, this can
degrade accuracy due to the current-sense amplifier’s
input offset (0.25mV typ). See Typical Operating
Characteristics to estimate the charge-current accuracy
at various set points.
Setting Input-Current Limit
The total input current, from a wall adapter or other DC
source, is the sum of the system supply current and the
current required by the charger. When the input current
exceeds the set input-current limit, the controller
decreases the charge current to provide priority to sys-
tem load current. System current normally fluctuates as
portions of the system are powered up or down. The
input-current-limit circuit reduces the power require-
ment of the AC wall adapter, which reduces adapter
cost. As the system supply rises, the available charge
current drops linearly to zero. Thereafter, the total input
current can increase without limit.
The total input current is the sum of the device supply cur-
rent, the charger input current, and the system load cur-
rent. The total input current can be estimated as follows:
Choose a current-sense resistor (RS1) to have a suffi-
cient power rating to handle the full system current. The
current-sense resistor can be reduced to improve effi-
ciency, but this degrades accuracy due to the current-
sense amplifier’s input offset (0.15mV typ). See Typical
Operating Characteristics to estimate the input current-
limit accuracy at various set points.
Automatic Power-Source Selection
The MAX17005B/MAX17006B/MAX17015B use an
external charge pump to drive the gate of an n-channel
adapter selection switch (N3 and Q1a). In Figure 1,
when the adapter is present, BST is biased 5V above
V ADAPTER so that N3 and Q1a are on, and Q1b is off.
As long as the adapter is present, even though the
charger is off, the power stage forces a refresh pulse to
the BST charge pump every 5ms.
When the adapter voltage is removed, the charger
stops generating BST refresh pulses and N4 forces N2
off, Q1b turns on and supplies power to the system
from the battery.
In Figure 1, D1 must have low forward-voltage drop and
low reverse-leakage current to ensure sufficient gate
drive at N3 and Q1a. A 100mA, low reverse-leakage
Schottky diode is the right choice.
Analog Input Current-Monitor Output
Use IINP to monitor the system-input current, which is
sensed across CSSP and CSSN. The voltage at IINP is
proportional to the input current:
I INPUT LOAD + CHARGE BATTERY
= I
I × V
V IN × η
I INPUT =
V IINP
RS 1 × G IINP × R IINP
where η is the efficiency of the DC-to-DC converter
(typically 85% to 95%).
In the MAX17005B/MAX17006B/MAX17015B, the volt-
age across CSSP and CSSN is constant at 60mV.
Choose the current-sense resistor, RS1, to set the input
current limit. For example, for 4A input current limit,
choose RS1 = 15m ? . For the input current-limit set-
tings, which cannot be achievable with standard sense
where I INPUT is the DC current supplied by the AC
adapter, G IINP is the transconductance of the sense
amplifier (2.8mA/V typ), and R IINP is the resistor con-
nected between IINP and ground. Typically, IINP has a
0 to 3.5V output-voltage range. Leave IINP unconnected
when not used.
RS1
resistor values, use a resistive voltage-divider between
CSSP and CSSN to tune the setting (Figure 4).
Rb
I INPUT _ LIMIT = × ( 1 + B )
RS 1 R A
60 mV R
CSSP
Ra
CSSN
To minimize power dissipation, first choose RS1
according to the closest available value. For conve-
nience, choose Ra = 6k ? and calculate Rb from the
above equation.
MAX17005B/MAX17006B/MAX17015B
Figure 4. Input Current-Limit Fine Tuning
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| AIUR-08-270K | INDUCTOR POWER 27UH 10% T/H |
| V48C48C75BF3 | CONVERTER MOD DC/DC 48V 75W |
| V48C48C75BF2 | CONVERTER MOD DC/DC 48V 75W |
| AIUR-08-220K | INDUCTOR POWER 22UH 10% T/H |
| MAX17005BETP+T | IC BATT CHARGER 1.2MHZ 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17006ETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17006ETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17006EVKIT+ | 功能描述:电池管理 1.2MHz Low-Cost High-Performance Chargers RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17007AGTI+ | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17007AGTI+T | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。