- 您现在的位置：买卖IC网 > PDF目录15533 > MAX17006BETP+T (Maxim Integrated Products)IC BATT CHARGER 1.2MHZ 20-TQFN PDF资料下载
参数资料
| 型号： | MAX17006BETP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/22页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER 1.2MHZ 20-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 多化学 |
| 电源电压： | 8 V ~ 26 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
1.2MHz, Low-Cost,
High-Performance Chargers
BDIV
OVP
SET POINT + 100mV
CSI
IMAX
11A
CCMP
LVC
IMIN
1A
ZCMP
1A
CSSP
OFF-TIME
COMPUTE
CSIN
Figure 6. DC-DC Converter Functional Diagram
R
S
OFF-TIME
ONE SHOT
Q
Q
DH DRIVER
DL DRIVER
The operation of the DC-to-DC controller is determined
by the following five comparators as shown in the func-
tional diagram in Figures 2 and 6:
? The IMIN comparator triggers a pulse in discontinu-
ous mode when the accumulated error is too high.
IMIN compares the control signal (LVC) against
10mV (referred at V CSIP - V CSIN ). When LVC is less
than this threshold, DHI and DLO are both forced
low. Indirectly, IMIN sets the peak inductor current
in discontinuous mode.
The high-side MOSFET on-time is terminated when
the current-sense signal exceeds 11A. A new cycle
cannot start until the IMAX comparator ’s output
goes low.
? The ZCMP comparator provides zero-crossing detec-
tion during discontinuous conduction. ZCMP com-
pares the current-sense feedback signal to 1A (RS2
= 10m ? ). When the inductor current is lower than
the 1A threshold, the comparator output is high,
and DLO is turned off.
?
?
The CCMP comparator is used for current-mode
regulation in continuous-conduction mode. CCMP
compares LVC against the inductor current. The
high-side MOSFET on-time is terminated when the
CSI voltage is higher than LVC.
The IMAX comparator provides a secondary cycle-
by-cycle current limit. IMAX compares CSI to
110mV (corresponding to 11A when RS2 = 10m ? ).
?
The OVP comparator is used to prevent overvoltage
at the output due to battery removal. OVP com-
pares BATT against the VCTL. When BATT is
100mV/cell above the set value, the OVP compara-
tor output goes high, and the high-side MOSFET
on-time is terminated. DHI and DLO remain off until
the OVP condition is removed.
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| AIUR-08-270K | INDUCTOR POWER 27UH 10% T/H |
| V48C48C75BF3 | CONVERTER MOD DC/DC 48V 75W |
| V48C48C75BF2 | CONVERTER MOD DC/DC 48V 75W |
| AIUR-08-220K | INDUCTOR POWER 22UH 10% T/H |
| MAX17005BETP+T | IC BATT CHARGER 1.2MHZ 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17006ETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17006ETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17006EVKIT+ | 功能描述:电池管理 1.2MHz Low-Cost High-Performance Chargers RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17007AGTI+ | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17007AGTI+T | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。