- 您现在的位置：买卖IC网 > PDF目录16559 > MAX17007AGTI+T (Maxim Integrated Products)IC CTRLR QPWM GRAPHICS 28TQFN PDF资料下载
参数资料
| 型号： | MAX17007AGTI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 28/35页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR QPWM GRAPHICS 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | Quick-PWM™ |
| 应用： | 电源 |
| 电流 - 电源： | 1.7mA |
| 电源电压： | 4.5 V ~ 26 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页
Dual and Combinable QPWM Graphics
Core Controllers for Notebook Computers
L = ?
f SW LOAD ( MAX ) LIR ? ? ? V IN ? ?
?
Quick-PWM Design Procedure
Firmly establish the input voltage range and maximum
load current before choosing a switching frequency
?
?
I
V IN ? V OUT ? ? V OUT ?
L = ?
? = 0 . 97 μ H
? 300 kHz × 15 A × 0 . 3 ? ? 12 V ?
and inductor operating point (ripple-current ratio). The
primary design trade-off lies in choosing a good switch-
ing frequency and inductor operating point, and the fol-
lowing four factors dictate the rest of the design:
? Input voltage range: The maximum value
(V IN(MAX) ) must accommodate the worst-case input
supply voltage allowed by the notebook ’s AC
adapter voltage. The minimum value (V IN(MIN) )
must account for the lowest input voltage after
drops due to connectors, fuses, and battery selec-
tor switches. If there is a choice at all, lower input
voltages result in better efficiency.
For example: I LOAD(MAX) = 15A, V IN = 12V, V OUT =
1.5V, f SW = 300kHz, 30% ripple current or LIR = 0.3:
? 12 V ? 1 . 5 V ? ? 1 . 5 V ?
? ?
Find a low-loss inductor having the lowest possible DC
resistance that fits in the allotted dimensions. Ferrite
cores are often the best choice, although powdered
iron is inexpensive and can work well at 200kHz. The
core must be large enough not to saturate at the peak
inductor current (I PEAK ):
I PEAK = I LOAD ( MAX ) ? 1 +
2 ?
?
Maximum load current: There are two values to
consider. The peak load current (I LOAD(MAX) ) deter-
mines the instantaneous component stresses and fil-
?
?
LIR ?
?
tering requirements, and thus drives output
capacitor selection, inductor saturation rating, and
the design of the current-limit circuit. The continuous
load current (I LOAD ) determines the thermal stress-
es and thus drives the selection of input capacitors,
MOSFETs, and other critical heat-contributing com-
ponents. Most notebook loads generally exhibit
I LOAD = I LOAD(MAX) x 80%.
In combined mode, I LOAD(MAX) is the per-phase maxi-
mum current, which is half the actual maximum load
current for the combined output.
Transient Response
The inductor ripple current impacts transient-response
performance, especially at low V IN - V OUT differentials.
Low inductor values allow the inductor current to slew
?
Switching frequency: This choice determines the
basic trade-off between size and efficiency. The
optimal frequency is largely a function of maximum
input voltage due to MOSFET switching losses that
are proportional to frequency and V IN 2 . The opti-
mum frequency is also a moving target due to rapid
faster, replenishing charge removed from the output fil-
ter capacitors by a sudden load step. The amount of
output sag is also a function of the maximum duty fac-
tor, which can be calculated from the on-time and mini-
mum off-time. The worst-case output sag voltage can
be determined by:
) 2 ? ? ? ? V OUT V IN T SW ? ? ? + t OFF ( M I N ) ?
(
L ? I LOAD(MAX)
? ? T SW ? t O F F ( MIN ) ?
? ? V IN ? V OUT ? ?
? ?
2 C OUT V OUT ? ?
?
improvements in MOSFET technology that are mak-
ing higher frequencies more practical.
Inductor operating point: This choice provides
trade-offs between size vs. efficiency and transient
response vs. output noise. Low inductor values pro-
vide better transient response and smaller physical
V SAG =
? ?
? ?
V IN ?
size, but also result in lower efficiency and higher
output noise due to increased ripple current. The
minimum practical inductor value is one that causes
the circuit to operate at the edge of critical conduc-
tion (where the inductor current just touches zero
where t OFF(MIN) is the minimum off-time (see the
Electrical Characteristics table).
The amount of overshoot due to stored inductor energy
can be calculated as:
with every cycle at maximum load). Inductor values
lower than this grant no further size-reduction benefit.
The optimum operating point is usually found
between 20% and 50% ripple current.
V SOAR
≈
( ? I LOAD ( MAX ) ) 2 L
N PH 2 C OUT V OUT
Inductor Selection
The per-phase switching frequency and operating point
(% ripple current or LIR) determine the inductor value
as follows:
where N PH is the number of active phases per output.
N PH is 1 for separate mode, and N PH is 2 for com-
bined-mode operation.
28
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| RCC12DRXS-S734 | CONN EDGECARD 24POS DIP .100 SLD |
| A1DXH-2036M | IDC CABLE - AKR20H/AE20M/X |
| RSC06DRTN-S734 | CONN EDGECARD 12POS DIP .100 SLD |
| ESM12DRSN | CONN EDGECARD 24POS DIP .156 SLD |
| P1330R-222K | INDUCTOR POWER 2.2UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17007BGTI+ | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17007BGTI+T | 制造商:Maxim Integrated Products 功能描述:DUAL AND COMBINABLE QPWM GRAPHICS CORE CONTROLLERS FOR NOTEB - Tape and Reel |
| MAX17007EVKIT+ | 功能描述:电源管理IC开发工具 QPWM Graphics Core Controller RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17007GTI+ | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17007GTI+T | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。