- 您现在的位置：买卖IC网 > PDF目录16559 > MAX17007AGTI+T (Maxim Integrated Products)IC CTRLR QPWM GRAPHICS 28TQFN PDF资料下载
参数资料
| 型号： | MAX17007AGTI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/35页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR QPWM GRAPHICS 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | Quick-PWM™ |
| 应用： | 电源 |
| 电流 - 电源： | 1.7mA |
| 电源电压： | 4.5 V ~ 26 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页
Dual and Combinable QPWM Graphics
Core Controllers for Notebook Computers
I LOAD 12 V OUT 1 ( V IN ? V OUT 1 ) + I LOAD 22 V OUT 2 ( V IN ? V OUT 2 )
I RMS = ? LOAD ? 2 V OUT ( V IN ? V OUT )
? ( I LOAD ) R DS ( ON )
PD ( NH Re sistive ) = ?
When only using ceramic output capacitors, output
overshoot (V SOAR ) typically determines the minimum
output capacitance requirement. Their relatively low
capacitance value can allow significant output over-
shoot when stepping from full-load to no-load condi-
tions, unless designed with a small inductance value
and high switching frequency to minimize the energy
transferred from the inductor to the capacitor during
load-step recovery.
Unstable operation manifests itself in two related but
distinctly different ways: double pulsing and feedback
loop instability. Double pulsing occurs due to noise on
the output or because the ESR is so low that there is
not enough voltage ramp in the output voltage signal.
This “fools” the error comparator into triggering a new
cycle immediately after the minimum off-time period
has expired. Double pulsing is more annoying than
harmful, resulting in nothing worse than increased out-
put ripple. However, it can indicate the possible pres-
ence of loop instability due to insufficient ESR. Loop
instability can result in oscillations at the output after
line or load steps. Such perturbations are usually
damped, but can cause the output voltage to rise
above or fall below the tolerance limits.
The easiest method for checking stability is to apply a
very fast zero-to-max load transient and carefully
observe the output voltage ripple envelope for over-
shoot and ringing. It can help to simultaneously monitor
the inductor current with an AC current probe. Do not
allow more than one cycle of ringing after the initial
step-response under/overshoot.
Input Capacitor Selection
The input capacitor must meet the ripple current
requirement (I RMS ) imposed by the switching currents.
The I RMS requirements can be determined by the fol-
lowing equation for a single-phase application:
I RMS =
V IN
In combined mode, the input RMS current simplifies to:
? I ?
? 2 V IN ?
where I LOAD is the combined output current of both
phases.
For most applications, nontantalum chemistries (ceram-
ic, aluminum, or OS-CON) are preferred due to their
resistance to inrush surge currents typical of systems
with a mechanical switch or connector in series with the
input. If the Quick-PWM controller is operated as the
second stage of a two-stage power-conversion system,
tantalum input capacitors are acceptable. In either con-
figuration, choose an input capacitor that exhibits less
than +10°C temperature rise at the RMS input current
for optimal circuit longevity.
Power-MOSFET Selection
Most of the following MOSFET guidelines focus on the
challenge of obtaining high load-current capability
when using high-voltage (> 20V) AC adapters. Low-
current applications usually require less attention.
The high-side MOSFET (N H ) must be able to dissipate
the resistive losses plus the switching losses at both
V IN(MIN) and V IN(MAX) . Calculate both of these sums.
Ideally, the losses at V IN(MIN) should be roughly equal to
losses at V IN(MAX) , with lower losses in between. If the
losses at V IN(MIN) are significantly higher than the losses
at V IN(MAX) , consider increasing the size of N H (reducing
R DS(ON) but with higher C GATE ). Conversely, if the loss-
es at V IN(MAX) are significantly higher than the losses at
V IN(MIN) , consider reducing the size of N H (increasing
R DS(ON) to lower C GATE ). If V IN does not vary over a
wide range, the minimum power dissipation occurs
where the resistive losses equal the switching losses.
Choose a low-side MOSFET that has the lowest possible
on-resistance (R DS(ON) ), comes in a moderate-sized
package (i.e., one or two 8-pin SOs, DPAK, or D 2 PAK),
and is reasonably priced. Make sure that the DL gate
driver can supply sufficient current to support the gate
charge and the current injected into the parasitic gate-
to-drain capacitor caused by the high-side MOSFET
turning on; otherwise, cross-conduction problems might
occur (see the MOSFET Gate Drivers (DH, DL) section).
MOSFET Power Dissipation
Worst-case conduction losses occur at the duty factor
extremes. For the high-side MOSFET (N H ), the worst-
case power dissipation due to resistance occurs at the
minimum input voltage:
? V OUT ? 2
? V IN ( MIN ) ?
Generally, a small high-side MOSFET is desired to
reduce switching losses at high input voltages.
However, the R DS(ON) required to stay within package
power dissipation often limits how small the MOSFET
can be. Again, the optimum occurs when the switching
losses equal the conduction (R DS(ON) ) losses. High-
side switching losses do not usually become an issue
until the input is greater than approximately 15V.
______________________________________________________________________________________
31
相关PDF资料 |
PDF描述 |
|---|---|
| RCC12DRXS-S734 | CONN EDGECARD 24POS DIP .100 SLD |
| A1DXH-2036M | IDC CABLE - AKR20H/AE20M/X |
| RSC06DRTN-S734 | CONN EDGECARD 12POS DIP .100 SLD |
| ESM12DRSN | CONN EDGECARD 24POS DIP .156 SLD |
| P1330R-222K | INDUCTOR POWER 2.2UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17007BGTI+ | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17007BGTI+T | 制造商:Maxim Integrated Products 功能描述:DUAL AND COMBINABLE QPWM GRAPHICS CORE CONTROLLERS FOR NOTEB - Tape and Reel |
| MAX17007EVKIT+ | 功能描述:电源管理IC开发工具 QPWM Graphics Core Controller RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17007GTI+ | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17007GTI+T | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。