- 您现在的位置：买卖IC网 > PDF目录17116 > MAX17015AETP+T (Maxim Integrated Products)IC BATT CHARGER 1.2MHZ 20TQFN PDF资料下载
参数资料
| 型号： | MAX17015AETP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/23页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER 1.2MHZ 20TQFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 多化学 |
| 电源电压： | 8 V ~ 26 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
1.2MHz, Low-Cost,
High-Performance Chargers
L × I RIPPLE
CC, CCI, CCS, and LVC Control Blocks
The MAX17005A/MAX17006A/MAX17015A control
input current (CCS control loop), charge current (CCI
control loop), or charge voltage (CC control loop),
depending on the operating condition. The three con-
trol loops, CC, CCI, and CCS are brought together
internally at the lowest voltage clamp (LVC) amplifier.
The output of the LVC amplifier is the feedback control
signal for the DC-DC controller. The minimum voltage
at the CC, CCI, or CCS appears at the output of the
LVC amplifier and clamps the other control loops to
within 0.3V above the control point. Clamping the other
two control loops close to the lowest control loop
ensures fast transition with minimal overshoot when
switching between different control loops (see the
Compensation section). The CCS and CCI loops are
compensated internally, and the CC loop is compen-
sated externally.
Continuous-Conduction Mode
With sufficiently large charge current, the MAX17005A/
MAX17006A/MAX17015s’ inductor current never cross-
es zero, which is defined as continuous-conduction
mode. The controller starts a new cycle by turning on
the high-side MOSFET and turning off the low-side
MOSFET. When the charge-current feedback signal
(CSI) is greater than the control point (LVC), the CCMP
comparator output goes high and the controller initiates
the off-time by turning off the high-side MOSFET and
turning on the low-side MOSFET. The operating fre-
quency is governed by the off-time and is dependent
upon V CSIN and V DCIN .
The on-time can be determined using the following
equation:
t ON =
V DCIN - V BATT
At the end of the computed off-time, the controller initi-
ates a new cycle if the control point (LVC) is greater
than 10mV (V CSIP - V CSIN referred), and the charge
current is less than the cycle-by-cycle current limit.
Restated another way, IMIN must be high, IMAX must
be low, and OVP must be low for the controller to initi-
ate a new cycle. If the peak inductor current exceeds
IMAX comparator threshold or the output voltage
exceeds the OVP threshold, then the on-time is termi-
nated. The cycle-by-cycle current limit effectively pro-
tects against overcurrent and short-circuit faults.
If during the off-time the inductor current goes to zero,
the ZCMP comparator output pulls high, turning off the
low-side MOSFET. Both the high- and low-side
MOSFETs are turned off until another cycle is ready to
begin. ZCOMP causes the MAX17005A/MAX17006A/
MAX17015A to enter into the discontinuous conduction
mode (see the Discontinuous Conduction section).
Discontinuous Conduction
The MAX17005A/MAX17006A/MAX17015A can also
operate in discontinuous conduction mode to ensure that
the inductor current is always positive. The MAX17005A/
MAX17006A/MAX17015A enter discontinuous conduction
mode when the output of the LVC control point falls below
10mV (referred at V CSIP - V CSIN ). For RS2 = 10m Ω , this
corresponds to a peak inductor current of 1A.
In discontinuous mode, a new cycle is not started until
the LVC voltage rises above IMIN. Discontinuous mode
operation can occur during conditioning charge of
overdischarged battery packs, when the charge cur-
rent has been reduced sufficiently by the CCS control
loop, or when the charger is in constant-voltage mode
with a nearly full battery pack.
Compensation
The charge voltage, charge current, and input current-
I RIPPLE = BATT OFF
where:
V × t
L
limit regulation loops are compensated separately. The
charge current and input current-limit loops, CCI and
CCS, are compensated internally, whereas the charge
voltage loop is compensated externally at CC.
The switching frequency can then be calculated:
f SW =
1
t ON + t OFF
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| SC43-470 | INDUCTOR SMD 47UH 0.54A 2.52MHZ |
| GMM11DRUS | CONN EDGECARD 22POS DIP .156 SLD |
| GCC18DRTN-S13 | CONN EDGECARD 36POS .100 EXTEND |
| 0210490818 | CABLE JUMPER 1.25MM .127M 13POS |
| GSC10DRXS-S734 | CONN EDGECARD 20POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17015BETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015BETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015ETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015ETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015ETP+TG51 | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。