- 您现在的位置：买卖IC网 > PDF目录15137 > MAX1845ETX+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 36-TQFN PDF资料下载
参数资料
| 型号： | MAX1845ETX+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/27页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 36-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 540kHz |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Dual, High-Efficiency, Step-Down
Controller with Accurate Current Limit
Table 3. Operating Mode Truth Table
ON1
ON2
SKIP
DL1/DL2
MODE
COMMENTS
Low-power shutdown state. If overvoltage protection is
GND
GND
X
High*/High*
Shutdown
enabled, DL1 and DL2 are forced to V DD , ensuring
overvoltage protection, I CC < 1μA (typ).
V CC
GND
V CC
Switching/High*
Run (PWM), Low Noise,
Side 1 Only
GND
V CC
V CC
GND
V CC
V CC
V CC
GND
V CC
V CC
V CC
V CC
GND
GND
GND
High*/Switching
Switching/
Switching
Switching/High*
High*/Switching
Switching/
Switching
Run (PWM), Low Noise,
Side 2 Only
Run (PWM), Low Noise,
Both Sides Active
Run (PWM/PFM), Skip
Mode, Side 1 Only
Run (PWM/PFM), Skip
Mode, Side 2 Only
Run (PWM/PFM), Skip
Mode, Both Sides Active
Low-noise, fixed frequency PWM at all load conditions.
Low noise, high I Q .
Normal operation with automatic PWM/PFM switchover
for pulse skipping at light loads. Best light-load
efficiency.
Fault latch has been set by overvoltage protection circuit,
V CC
V CC
X
High*/High*
Fault
undervoltage protection circuit, or thermal shutdown.
Device will remain in fault mode until V CC power is
cycled or ON1/ON2 is toggled.
*DL_ high only if overvoltage protection enabled (see Output Overvoltage Protection section).
of multiple-output applications that use a flyback trans-
former or coupled inductor.
Current-Limit Circuit (ILIM_)
The current-limit circuit employs a unique “valley” current-
sensing algorithm. If the magnitude of the current-sense
signal at CS_ is above the current-limit threshold, the
PWM is not allowed to initiate a new cycle (Figure 5). The
actual peak current is greater than the current-limit
threshold by an amount equal to the inductor ripple cur-
rent. Therefore, the exact current-limit characteristic and
maximum load capability are a function of the sense
resistance, inductor value, and battery voltage.
There is also a negative current limit that prevents exces-
sive reverse inductor currents when V OUT is sinking cur-
rent. The negative current-limit threshold is set to
approximately 120% of the positive current limit and
therefore tracks the positive current limit when ILIM is
adjusted.
The current-limit threshold is adjusted with an internal
5μA current source and an external resistor at ILIM. The
current-limit threshold adjustment range is from 25mV
to 250mV. In the adjustable mode, the current-limit
threshold voltage is precisely 1/10 the voltage seen at
ILIM. The threshold defaults to 50mV when ILIM is con-
nected to V CC . The logic threshold for switchover to the
50mV default value is approximately V CC - 1V.
Carefully observe the PC board layout guidelines to
ensure that noise and DC errors do not corrupt the cur-
rent-sense signal seen by CS_ and GND. Mount or
place the IC close to the low-side MOSFET and sense
resistor with short, direct traces, making a Kelvin sense
connection to the sense resistor. In Figure 1, the
Schottky diodes (D1 and D2) provide current paths
parallel to the Q2/R SENSE and Q4/R SENSE current
paths, respectively. Accurate current sensing requires
D1/D2 to be off while Q2/Q4 conducts. Avoid large cur-
rent-sense voltages that, combined with the voltage
across Q2/Q4, would allow D1/D2 to conduct. If very
large sense voltages are used, connect D1/D2 in paral-
lel with Q2/Q4 only.
MOSFET Gate Drivers (DH_, DL_)
The DH and DL drivers are optimized for driving mod-
erate-size, high-side and larger, low-side power
MOSFETs. This is consistent with the low duty factor
seen in the notebook CPU environment, where a large
V BATT - V OUT differential exists. An adaptive dead-time
circuit monitors the DL output and prevents the high-
side FET from turning on until DL is fully off. There must
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1845EEI+T | IC REG CTRLR BUCK PWM CM 28-QSOP |
| GEC43DRAS-S734 | CONN EDGECARD 86POS .100 R/A SLD |
| GSC28DREN-S13 | CONN EDGECARD 56POS .100 EXTEND |
| GMC28DREN-S13 | CONN EDGECARD 56POS .100 EXTEND |
| VI-2T4-EY-F4 | CONVERTER MOD DC/DC 48V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1845ETX-TG068 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1845EVKIT | 功能描述:电源管理IC开发工具 Evaluation Kit for the MAX1845 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX1846EUB | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1846EUB+ | 功能描述:电流型 PWM 控制器 Current-Mode Invert PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1846EUB+T | 功能描述:电流型 PWM 控制器 Current-Mode Invert PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。