- 您现在的位置：买卖IC网 > PDF目录9850 > MAX194BEWE+T (Maxim Integrated Products)IC ADC 14BIT 85KSPS 16-SOIC PDF资料下载
参数资料
| 型号： | MAX194BEWE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 85KSPS 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 位数： | 14 |
| 采样率（每秒）： | 85k |
| 数据接口： | QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 80mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
MAX194
DC Accuracy
If DC accuracy is important, choose a buffer with an
offset much less than the MAX194’s maximum offset
(±1 LSB = ±488V for a ±4V input range), or whose off-
set can be trimmed while maintaining good stability
over the required temperature range.
Recommended Circuits
Figure 14 shows a good circuit for DC and low-frequen-
cy use. The MAX400 has very low offset (10V) and
drift (0.2V/°C), and low voltage noise (10nV/
√Hz) as
well. However, its gain-bandwidth product (GBW) is
much too low to drive AIN directly, so the analog input
is bypassed to present a low impedance at high fre-
quencies. The large bypass capacitor is isolated from
the amplifier output by a 100
resistor, which provides
additional noise filtering. Since the ±15V supplies
exceed the AIN range, add protection diodes at AIN.
Figure 15 shows a wide-bandwidth amplifier (MAX427)
driving a wideband video buffer, which is capable of dri-
ving AIN and a small bypass capacitor (for noise reduc-
tion) directly. The video buffer is inside the MAX427’s
feedback loop, providing good DC accuracy, while the
buffer’s low output impedance and high current capabil-
ity provide good AC performance. AIN is diode-
clamped to the ±5V rails to prevent overvoltage. The
MAX427’s 15V maximum offset voltage, 0.8V/°C maxi-
mum drift, and less than 5nV/
√Hz noise specifications
make this an excellent choice for AC/DC use.
If ±15V supplies are unavailable, Figure 16’s circuit works
very well with the ±5V analog supplies used by the
MAX194. The MAX410 has a minimum ±3.5V common-
mode input range, with a similar output voltage swing,
which allows use of a reference voltage to 3.5V. The offset
voltage (250V), drift (1V/°C), unity-gain bandwidth
(28MHz), and low voltage noise (2.4nV/
√Hz) are appropri-
ate for 14-bit performance. The 0.01F bypass capacitor
improves the noise performance.
Operating Modes and SPI/QSPI Interfaces
The two basic interface modes are defined according
to whether serial data is received during the conversion
(clocked with CLK, SCLK unused) or in bursts between
conversions (clocked with SCLK). Each mode is pre-
sented interfaced to a QSPI processor, but is also com-
patible with SPI.
Mode 1 (Simultaneous
Conversion and Data Transfer)
In this mode, each data bit is read from the MAX194 dur-
ing the conversion as it is determined. SCLK is grounded
and CLK is used as both the conversion clock and the
serial data clock. Figure 17 shows a QSPI processor
connected to the MAX194 for use in this mode and
Figure 18 is the associated timing diagram.
In addition to the standard QSPI interface signals, gener-
al I/O lines are used to monitor EOC and to drive
BP/UP/SHDN and RESET. The two general output pins
may not be necessary for a given application and, if I/O
lines are unavailable, the EOC connection can be omit-
ted as well.
The EOC signal is monitored during calibration to deter-
mine when calibration is finished and before beginning
a conversion to ensure the MAX194 is not in mid-con-
version, but it is possible for a system to ignore EOC
completely. On power-up or after pulsing RESET low,
the P must provide 14,000 CLK cycles to complete the
calibration sequence (Figure 2). One way to do this is
to toggle CLK and monitor EOC until it goes low, but it
is possible to simply count 14,000 CLK cycles to com-
plete the calibration. Similarly, it is unnecessary to
check the status of EOC before beginning a conversion
if you are sure the last conversion is complete. This can
be done by ensuring that every conversion consists of
at least 20 CLK cycles.
14-Bit, 85ksps ADC with 10A Shutdown
16
______________________________________________________________________________________
MAX194
QSPI
GPT
BP/UP/SHDN
CLK
SCLK
EOC
DOUT
RESET
CONV
CS
*OC3
SCK
*IC1
MISO
*OC2
* THE USE OF THESE SIGNALS ADDS FLEXIBILITY AND FUNCTIONALITY
BUT IS NOT REQUIRED TO IMPLEMENT THE INTERFACE.
PCS0
Figure 17. MAX194 Connection to QSPI Processor Clocking
Data Out During Conversions
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J4X-MX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| MX7828LCWI+ | IC ADC 8BIT HS 28-SOIC |
| MS27473P16B55S | CONN PLUG 55POS STRAIGHT W/SCKT |
| VE-J4X-MX-F3 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-J4X-MX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX194BMDE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194EVC16-DIP | 功能描述:模数转换器 - ADC Programmers, Development Systems RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194EVKIT-DIP | 功能描述:数据转换 IC 开发工具 Programmers, Development Systems RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX19505ETM+ | 功能描述:模数转换器 - ADC 8-Bit 2Ch 65Msps 1.8V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX19505ETM+T | 功能描述:模数转换器 - ADC 8-Bit 2Ch 65Msps 1.8V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。