- 您现在的位置：买卖IC网 > PDF目录10485 > MAX195BCPE+ (Maxim Integrated Products)IC ADC 16BIT 85KSPS SHTDN 16-DIP PDF资料下载
参数资料
| 型号： | MAX195BCPE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 85KSPS SHTDN 16-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 25 |
| 位数： | 16 |
| 采样率（每秒）： | 85k |
| 数据接口： | QSPI?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 80mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
| 产品目录页面： | 1393 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页
MAX195
after the end of the previous conversion and EOC will
go high on the following CLK falling edge (Figure 4).
External Clock
The conversion clock (CLK) should have a duty cycle
between 25% and 75% at 1.7MHz (the maximum clock
frequency). For lower frequency clocks, ensure the min-
imum high and low times exceed 150ns. The minimum
clock rate for accurate conversion is 125Hz for temper-
atures up to +70°C or 1kHz at +125°C due to leakage
of the sampling capacitor array. In addition, CLK
should not remain high longer than 50ms at tempera-
tures up to +70°C or 500s at +125°C. If CLK is held
high longer than this, RESET must be pulsed low to initi-
ate a recalibration because it is possible that state
information stored in internal dynamic memory may be
lost. The MAX195’s clock can be stopped indefinitely if
it is held low.
If the frequency, duty cycle, or other aspects of the
clock signal’s shape change, the offset created by cou-
pling between CLK and the analog inputs (AIN and
REF) changes. Recalibration corrects for this offset and
restores DC accuracy.
Output Data
The conversion result, clocked out MSB first, is avail-
able on DOUT only when CS is held low. Otherwise,
DOUT is in a high-impedance state. There are two ways
to read the data on DOUT. To read the data bits as they
are determined (at the CLK clock rate), hold CS low
during the conversion. To read results between conver-
sions, hold CS low and clock SCLK at up to 5MHz.
If you read the serial data bits as they are determined,
EOC frames the data bits (Figure 6). Conversion begins
with the first falling CLK edge, after CONV goes low
and the input signal has been acquired. Data bits are
shifted out of DOUT on subsequent falling CLK edges.
Clock data in on CLK’s rising edge or, if the clock
speed is greater than 1MHz, on the following falling
edge of CLK to meet the maximum CLK-to-DOUT tim-
ing specification. See the
Operating Modes and
SPI/QSPI Interfaces section for additional informa-
tion. Reading the serial data during the conversion
results in the maximum conversion throughput,
because a new conversion can begin immediately after
the input acquisition period following the previous con-
version.
16-Bit, 85ksps ADC with 10A Shutdown
8
_______________________________________________________________________________________
TRACK/HOLD
CLK
CONVERSION
BEGINS
CONVERSION
ENDS
tAQ
*
* THE FALLING EDGE OF CONV MUST OCCUR IN THIS REGION
tCEL
tCW
tCEH
tCC2
tCC1
EOC
CONV
Figure 4. Initiating Conversions—Less than 3 CLK cycles since end of previous conversion.
SPI/QSPI are trademarks of Motorola Corp.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3106E12S-3SX | CONN PLUG 2POS STRAIGHT W/SCKT |
| MAX170CEWE+ | IC ADC 12BIT SERIAL 16-SOIC |
| MS3106E12S-3SW | CONN PLUG 2POS STRAIGHT W/SCKT |
| VE-BT0-IV-F2 | CONVERTER MOD DC/DC 5V 150W |
| VE-26N-IV-B1 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX195BCPE+ | 功能描述:模数转换器 - ADC 16-Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX195BCPE+T | 制造商:Maxim Integrated Products 功能描述:16-BIT, 85KSPS ADC WITH 10UA SHUTDOWN - Tape and Reel |
| MAX195BCWE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX195BCWE+ | 功能描述:模数转换器 - ADC 16-Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX195BCWE+T | 功能描述:模数转换器 - ADC 16-Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。