- 您现在的位置：买卖IC网 > PDF目录10485 > MAX195BCPE+ (Maxim Integrated Products)IC ADC 16BIT 85KSPS SHTDN 16-DIP PDF资料下载
参数资料
| 型号： | MAX195BCPE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 85KSPS SHTDN 16-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 25 |
| 位数： | 16 |
| 采样率（每秒）： | 85k |
| 数据接口： | QSPI?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 80mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
| 产品目录页面： | 1393 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MAX195
If ±15V supplies are unavailable, Figure 16’s circuit
works very well with the ±5V analog supplies used by
the MAX195. The MAX410 has a minimum ±3.5V com-
mon-mode input range, with a similar output voltage
swing, which allows use of a reference voltage up to
3.5V. The offset voltage (250V) is about 2LSB. The
drift (1V/°C), unity-gain bandwidth (28MHz), and low
voltage noise (2.4nV/
√Hz) are appropriate for 16-bit
performance.
Operating Modes and SPI/QSPI Interfaces
The two basic interface modes are defined according
to whether serial data is received during the conversion
(clocked with CLK, SCLK unused) or in bursts between
conversions (clocked with SCLK). Each mode is pre-
sented interfaced to a QSPI processor, but is also com-
patible with SPI.
Mode 1 (Simultaneous
Conversion and Data Transfer)
In this mode, each data bit is read from the MAX195
during the conversion as it is determined. SCLK is
grounded and CLK is used as both the conversion
clock and the serial data clock. Figure 17 shows a
QSPI processor connected to the MAX195 for use in
this mode and Figure 18 is the associated timing dia-
gram.
In addition to the standard QSPI interface signals, gen-
eral I/O lines are used to monitor EOC and to drive
BP/UP/SHDN and RESET. The two general output pins
may not be necessary for a given application and, if I/O
lines are unavailable, the EOC connection can be omit-
ted as well.
The EOC signal is monitored during calibration to
determine when calibration is finished and before
beginning a conversion to ensure the MAX195 is not in
mid-conversion, but it is possible for a system to ignore
EOC completely. On power-up or after pulsing RESET
low, the P must provide 14,000 CLK cycles to com-
plete the calibration sequence (Figure 2). One way to
do this is to toggle CLK and monitor EOC until it goes
low, but it is possible to simply count 14,000 CLK
cycles to complete the calibration. Similarly, it is
unnecessary to check the status of EOC before begin-
ning a conversion if you are sure the last conversion is
complete. This can be done by ensuring that every
conversion consists of at least 20 CLK cycles.
Data is clocked out of the MAX195 on CLK’s falling
edge and can be clocked into the P on the rising
edge or the following falling edge. If you clock data in
on the rising edge (SPI/QSPI with CPOL = 0 and CPHA
= 0; standard MicroWire: Hitachi H8), the maximum
CLK rate is given by:
where tCD is the MAX195’s CLK-to-DOUT valid delay
and tSD is the data setup time for your P.
f
=
/
1
t
+ t
CLK(max)
1
2
CD
SD
16-Bit, 85ksps ADC with 10A Shutdown
16
______________________________________________________________________________________
MAX195
QSPI
GPT
BP/UP/SHDN
CLK
SCLK
EOC
DOUT
RESET
CONV
CS
*OC3
SCK
*IC1
MISO
*OC2
* THE USE OF THESE SIGNALS ADDS FLEXIBILITY AND FUNCTIONALITY
BUT IS NOT REQUIRED TO IMPLEMENT THE INTERFACE.
PCS0
Figure 17. MAX195 Connection to QSPI Processor Clocking
Data Out During Conversions
MAX410
4
7
6
2
3
IN
+5V
-5V
0.1
F
0.01
F
22
510
0.1
F
AIN
Figure 16. ±5V Buffer for AC/DC Use Has ±3.5V Swing
MicroWire is a trademark of National Semiconductor Corp.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3106E12S-3SX | CONN PLUG 2POS STRAIGHT W/SCKT |
| MAX170CEWE+ | IC ADC 12BIT SERIAL 16-SOIC |
| MS3106E12S-3SW | CONN PLUG 2POS STRAIGHT W/SCKT |
| VE-BT0-IV-F2 | CONVERTER MOD DC/DC 5V 150W |
| VE-26N-IV-B1 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX195BCPE+ | 功能描述:模数转换器 - ADC 16-Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX195BCPE+T | 制造商:Maxim Integrated Products 功能描述:16-BIT, 85KSPS ADC WITH 10UA SHUTDOWN - Tape and Reel |
| MAX195BCWE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX195BCWE+ | 功能描述:模数转换器 - ADC 16-Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX195BCWE+T | 功能描述:模数转换器 - ADC 16-Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。