- 您现在的位置：买卖IC网 > PDF目录13119 > MAX1997ETJ+ (Maxim Integrated Products)IC PWR SUPPLY TFT LCD 32TQFN PDF资料下载
参数资料
| 型号： | MAX1997ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 23/31页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY TFT LCD 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 应用： | 控制器，TFT LCD |
| 输入电压： | 2.7 V ~ 5.5 V |
| 输出数： | 5 |
| 输出电压： | 2.7 V ~ 13 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页
Quintuple/Triple-Output TFT LCD Power Supplies
with Fault Protection and VCOM Buffer
The frequencies of the zero and pole for the lead com-
pensation are:
When adding lag compensation, always check the loop
stability by monitoring the transient response to a
2 π ? R 9 +
? × C 9
f Z_LEAD =
f P_LEAD =
1
2 π ( R 7 + R 9 ) × C 9
1
? R 7 × R 8 ?
? R 7 × R 8 ?
pulsed output load.
The circuit of Figure 1 works well without compensation.
The circuit of Figure 9 uses lag compensation to allow
higher value FB divider resistors, at the expense of
transient response speed, potentially requiring higher
value output capacitors (see Typical Operating
f P_LAG =
2 π ? R 10 +
? × C 10
f Z_LAG =
At high frequencies, R9 is effectively in parallel with R7,
determining the amount of added high-frequency gain. If
R9 is very large, there is no added gain and as R9
approaches zero, the added gain approaches the inverse
of the feedback divider ’ s attenuation. A typical value for
R9 is greater than half of R7. The value of C9 determines
the frequency placement of the zero and pole. A typical
value of C9 is between 100pF and 10nF. When adding
lead compensation, always check the loop stability by
monitoring the transient response to a pulsed output load.
Adding lag compensation (an RC network from FB to
ground) decreases the loop bandwidth and improves
FB noise immunity. Lag compensation slows the tran-
sient response but can increase stability margin, which
can be needed for particular component choices, a
poor layout, or high values of FB divider resistors (R8
greater than 1.5k ? ).
Lag compensation adds a pole-zero pair, attenuating
gain at higher frequencies and lowering loop band-
width. The frequencies of the pole and zero for lag com-
pensation depend on the feedback divider resistors and
the RC network between FB and GND (Figure 9).
The frequencies of the pole and zero for the lag com-
pensation are:
1
? R 7 × R 8 ?
? R 7 + R 8 ?
1
2 π ( R 10 × C 10 )
At high frequencies, R10 is effectively in parallel with
R8, increasing the divider attenuation ratio. If R10 is
very large, the attenuation ratio remains unchanged
and as R10 approaches zero, the attenuation ratio
approaches infinity. A typical value for R10 is greater
than 0.1 times R8. If high-value divider resistors are
used, choose R10 < 1.5k ? for FB noise immunity. The
value of C10 determines the frequency placement of
the pole and zero. A typical value of C10 is between
100pF and 1000pF.
Characteristics ). Using one of these two circuits is
recommended.
Using Compensation for Improved Soft-Start
The digital soft-start of the main step-up regulator limits
the average input current during startup. If even
smoother startup is needed, add a low-frequency lead
compensation network (Figure 9). The improved soft-
start is active only during startup when the output volt-
age rises. Positive changes in the output are
instantaneously coupled to the FB pin through D1 and
feed-forward capacitor C9. This arrangement generates
a smoothly rising output voltage. When the output volt-
age reaches regulation, capacitor C9 charges up
through R9 and diode D1 turns off. If desired, C9 and
R9 can be chosen also to provide some lead compen-
sation in normal operation. In most applications, lead
compensation is not needed, and can be disabled by
making R9 large. With R9 much greater than R7, the
pole and the zero in the compensation network are very
close to one another and cancel out after startup, elimi-
nating the effect of the lead compensation.
Input Capacitor
The input capacitor (C IN ) reduces the current peaks
drawn from the input supply and reduces noise injec-
tion into the device. A 10μF ceramic capacitor is used
in the standard application circuit (Figure 1) because of
the high source impedance seen in typical lab setups.
Actual applications usually have much lower source
impedance since the step-up regulator often runs
directly from the output of another regulated supply.
Typically, C IN may be reduced below the values used
in the standard applications circuit. Ensure a low-noise
supply at the IN pin by using adequate C IN . Alter-
natively, greater voltage variation can be tolerated on
C IN if IN is decoupled from C IN using an RC lowpass fil-
ter (see R1, C1 in Figure 1).
Rectifier Diode
The MAX1997/MAX1998s ’ high switching frequency
demands a high-speed rectifier. Schottky diodes are rec-
ommended for most applications because of their fast
recovery time and low forward voltage. In general, a 1A
Schottky diode complements the internal MOSFET well.
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| EBM28DTMT-S189 | CONN EDGECARD 56POS R/A .156 SLD |
| ABM15DSES-S243 | CONN EDGECARD 30POS .156 EYELET |
| VI-J6V-CX | CONVERTER MOD DC/DC 5.8V 75W |
| VE-2WB-EW-B1 | CONVERTER MOD DC/DC 95V 100W |
| GBM31DTMT-S189 | CONN EDGECARD 62POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1997ETJ+ | 功能描述:其他电源管理 Quint/Triple-Out TFT LCD Power Supply RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| MAX1997ETJ+T | 功能描述:LCD 驱动器 Quint/Triple-Out TFT LCD Power Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1997ETJ-T | 功能描述:其他电源管理 RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| MAX1997EVKIT | 制造商:Maxim Integrated Products 功能描述:QUINTUPLE/TRIPLE OUTPUT TFT LCD POWER SUPPLIE - Bulk |
| MAX19983A | 功能描述:上下转换器 RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
发布紧急采购，3分钟左右您将得到回复。