- 您现在的位置：买卖IC网 > PDF目录18778 > MAX2112CTI+T (Maxim Integrated)IC TUNER DIR-CONV DVB-S2 28-TQFN PDF资料下载
参数资料
| 型号： | MAX2112CTI+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 15/19页 |
| 文件大小： | 0K |
| 描述： | IC TUNER DIR-CONV DVB-S2 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 925MHz ~ 2.175GHz |
| 应用： | 数字 TV，CATV，机顶盒 |
| 电流 - 接收： | 100mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 电源电压： | 3.13 V ~ 3.47 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
MAX2112
Complete, Direct-Conversion
Tuner for DVB-S2 Applications
S
T
A
R
T
DEVICE
ADDRESS
1100000
R/W
0
A
C
K
REGISTER
ADDRESS
00000000
A
C
K
S
T
A
R
T
DEVICE
ADDRESS
1100000
R/W
1
A
C
K
REG 00
DATA
xxxxxxxx
A
C
K
REG 01
DATA
xxxxxxxx
A
C
K
REG 02
DATA
xxxxxxxx
N
A
C
K
S
T
O
P
Figure 3. Example: Receive Data from Read Registers
Read Cycle
When addressed with a read command, the MAX2112
allows the master to read back a single register, or mul-
Table 16. Maximum Crystal ESR
Requirement
tiple successive registers.
ESR MAX ( )
XTAL FREQUENCY (MHz)
A read cycle begins with the bus master issuing a
START condition followed by the 7 slave address bits
and a write bit (R/ W = 0). The MAX2112 issues an ACK if
80
60
12 < f XTAL
14 < f XTAL
14
30
the slave address byte is successfully received. The bus
master must then send the address of the first register it
wishes to read (see Table 1 for register addresses). The
slave acknowledges the address. Then, a START condi-
tion is issued by the master, followed by the 7 slave
address bits and a read bit (R/ W = 1). The MAX2112
issues an ACK if the slave address byte is successfully
received. The MAX2112 starts sending data MSB first
with each SCL clock cycle. At the 9th clock cycle, the
master can issue an ACK and continue to read succes-
sive registers, or the master can terminate the transmis-
sion by issuing a NACK. The read cycle does not
terminate until the master issues a STOP condition.
Figure 3 illustrates an example in which registers 0
through 2 are read back.
Application Information
The MAX2112 downconverts RF signals in the 925MHz to
2175MHz range directly to the baseband I/Q signals. The
devices are targeted for digital DBS tuner applications.
RF Input
The RF input of the MAX2112 is internally matched to
75 ? . Only a DC-blocking capacitor is needed. See the
Typical Application Circuit.
RF Gain Control
The MAX2112 features a variable-gain low-noise ampli-
fier providing 73dB of RF gain range. The voltage con-
trol (VGC) range is 0.5V (minimum attenuation) to 2.7V
(maximum attenuation).
Baseband Variable-Gain Amplifier
The receiver baseband variable-gain amplifiers provide
15dB of gain control range programmable in 1dB
steps. The VGA gain can be serially programmed
through the SPI interface by setting bits BBG[3:0] in the
Control register.
Maxim Integrated
Baseband Lowpass Filter
The MAX2112 includes a programmable on-chip
7th-order Butterworth filter. The filter -3dB corner fre-
quency can be adjusted from approximately 4MHz to
40MHz by programming the LPF[7:0] register using the
following equation:
LPF[7:0] dec = (f -3dB - 4MHz)/0.29MHz + 12,
where f -3dB is in units of MHz.
Total device supply current depends on the filter BW
setting. See Supply Current vs. Baseband Filter Cutoff
Frequency in the Typical Operating Characteristics for
more information.
DC Offset Cancellation
The DC offset cancellation is required to maintain the
I/Q output dynamic range. Connecting an external
capacitor between IDC+ and IDC- forms a highpass fil-
ter for the I channel and an external capacitor between
QDC+ and QDC- forms a highpass filter for the Q chan-
nel. Keep the value of the external capacitor less than
47nF to form a typical highpass corner of 250Hz.
XTAL Oscillator
The MAX2112 contains an internal reference oscillator,
reference output divider, and output buffer. All that is
required is to connect a crystal through a series 1nF
capacitor. To minimize parasitics, place the crystal and
series capacitor as close as possible to pin 14 (XTAL
pin). See Table 16 for crystal (XTAL) ESR (equivalent
series resistance) requirements.
VCO Autoselect (VAS)
The MAX2112 includes 24 VCOs. The local oscillator
frequency can be manually selected by programming
the VCO[4:0] bits in the VCO register. The selected VCO
is reported in the Status Byte-2 register (see Table 15).
15
相关PDF资料 |
PDF描述 |
|---|---|
| MAX7034AUI/V+ | IC RCVR 315/433MHZ ASK 28TSSOP |
| 6106 | PROBE RF DMM KIT 1GHZ |
| EKMB1301112 | SENSOR MOTION PIR DIGITAL BLACK |
| EKMB1301111 | SENSOR MOTION PIR DIGITAL WHITE |
| EKMB1301113 | SENSOR MOTION PIR DIGITAL WHITE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2112ETI/GG8 | 制造商:Maxim Integrated Products 功能描述:COMPLETE, DIRECT-CONVERSION TUNER FOR DVB-S2 APPLICATIONS - Rail/Tube |
| MAX2112ETI+ | 功能描述:调谐器 Direct Conv Tuner Tuner for DVB-S2 RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
| MAX2112ETI+T | 功能描述:调谐器 Direct Conv Tuner Tuner for DVB-S2 RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
| MAX2112EVKIT+ | 功能描述:射频开发工具 MAX2112 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX2113EVKIT | 功能描述:射频开发工具 MAX2113 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。