- 您现在的位置：买卖IC网 > Datasheet目录472 > MAX2120EVKIT+ (Maxim Integrated)KIT EVAL FOR MAX2120 Datasheet资料下载
参数资料
| 型号： | MAX2120EVKIT+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 18/21页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX2120 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 调谐器 |
| 频率： | 925MHz ~ 2.175GHz |
| 适用于相关产品： | MAX2120 |
| 已供物品： | 板 |
Complete, Direct-Conversion Tuner for DVB-S
and Free-to-Air Applications
3-Bit ADC
The MAX2120 has an internal 3-bit ADC connected to
the VCO tune pin (VTUNE). This ADC can be used for
checking the lock status of the VCOs.
Table 15 summarizes the ADC trip points, and the VCO
lock indication. The VCO autoselect routine will only
select a VCO in the “VAS locked” range. This allows
room for a VCO to drift over temperature and remain in
a valid “locked” range.
The ADC must first be enabled by setting the ADE bit in
the VCO register. The ADC reading is latched by a sub-
sequent programming of the ADC latch bit (ADL = 1).
The ADC value is reported in the Status Byte-2 register
(see Table 13).
Table 15. ADC Trip Points and Lock Status
Standby Mode
The MAX2120 features normal operating mode and
standby mode using the I 2 C interface. Setting a logic-
high to the PWDN bit in the Control register enables
power-down. In this mode, all circuitries except for the 2-
wire-compatible bus are disabled, allowing for program-
ming of the MAX2120 registers while in power-down.
In all cases, register settings loaded prior to entering
shutdown are saved upon transition back to active
mode. Default register values are provided for the
user’s convenience only. It’s the user’s responsibility to
load all the registers no sooner than 100μs after the
device is powered up.
Layout Considerations
The MAX2120 EV kit serves as a guide for PCB
layout. Keep RF signal lines as short as possible to mini-
ADC[2:0]
000
001
010
101
110
111
LOCK STATUS
Out of Lock
Locked
VAS Locked
VAS Locked
Locked
Out of Lock
mize losses and radiation. Use controlled impedance on
all high-frequency traces. For proper operation, the
exposed paddle must be soldered evenly to the board’s
ground plane. Use abundant vias beneath the exposed
paddle for maximum heat dissipation. Use abundant
ground vias between RF traces to minimize undesired
coupling. Bypass each V CC pin to ground with a 1nF
capacitor placed as close as possible to the pin.
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX2121EVKIT# | KIT EVAL FOR MAX2121 |
| MAX2130EVKIT | EVAL KIT MAX2130 |
| MAX2140EVKIT | EVAL KIT MAX2140 |
| MAX2150ETI+T | IC MODULATOR I/Q WIDE 28TQFN |
| MAX2160EVKIT | EVAL KIT MAX2160 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2120EVKIT+ | 功能描述:射频开发工具 MAX2120 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX2121 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Complete Direct-Conversion L-Band Tuner |
| MAX2121_V1 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Complete Direct-Conversion L-Band Tuner |
| MAX2121ETI | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Complete Direct-Conversion L-Band Tuner 925MHz to 2175MHz Frequency Range |
| MAX2121ETI+ | 功能描述:调谐器 Direct-Conversion L-Band Tuner RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。