- 您现在的位置：买卖IC网 > PDF目录1938 > MAX3107EAG+ (Maxim Integrated Products)IC UART SPI/I2C 128 FIFO 24SSOP PDF资料下载
参数资料
| 型号： | MAX3107EAG+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 26/52页 |
| 文件大小： | 0K |
| 描述： | IC UART SPI/I2C 128 FIFO 24SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 58 |
| 特点： | 内部振荡器 |
| 通道数： | 4，QUART |
| FIFO's： | 128 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.35 V ~ 3.6 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
SPI/I2C UART with 128-Word FIFOs
Bit 7: EchoSuprs
Set the EchoSuprs bit high so that the MAX3107’s receiver gates any data it receives when its transmitter is busy
transmitting. In half-duplex communication (like IrDA and RS-485) this allows blocking of the locally echoed data. The
receiver can block data for an extended time after the transmitter ceases transmission by programming a hold time in
HDplxDelay[3:0] bits.
Bit 6: MultiDrop
Set the MultiDrop bit high to enable the 9-bit multidrop mode. If this bit is set, parity checking is not performed by the
receiver and parity generation is not done by the transmitter. The parity error bit, LSR[2], has a different meaning in
this case. The parity error bit represents the 9th bit (address/data indication) that is received with each 9-bit character.
Bit 5: Loopback
Set the Loopback bit high to enable internal local loopback mode. This internally connects TX to RX and also RTS/
CLKOUT to CTS. In local loopback mode, the TX output and the RX output are disconnected from the internal transmit-
ter and receiver. The TX output is in three-state. The RTS output remains connected to the internal logic and reflects the
logic state programmed in LCR[7]. The CTS input is disconnected from RTS and the internal logic. CTS thus remains
in a high-impedance state.
Bit 4: SpecialChr
The SpecialChr bit enables special character detection. The receiver can detect up to four special characters, as
selected in FlowCtrl:[5:4] and defined in the XON1, XON2, XOFF1 and/or XOFF2 registers, possibly in combination with
GPIO_ inputs, enabled through FlowCtrl[2]: GPIAddr. When a special character is received it is put into the RxFIFO and
a special character detect interrupt ISR[1] is generated.
Special character detection can be used in addition to auto XON/XOFF flow control, if enabled through FlowCtrl[3]. In
this case XON/OFF flow control is then limited to single character XON and XOFF and only two special characters can
then be defined (in XON2 and XOFF2).
Bit 3: RxEmtyInv
The RxEmtyInv bit inverts the meaning of the receiver empty interrupt: ISR[6]: RxEmtyInt. If RxEmtyInv is set low (default
state), the ISR[6] interrupt is generated when the receive FIFO is empty. If the RxEmtyInv is set high, the ISR[6] interrupt
is generated when data is put into the empty receive FIFO.
Bit 2: RxTrigInv
The RxTrigInv bit inverts the meaning of the RxFIFO triggering. When set, an ISR[3]: RFifoTrigInt is generated when
the RxFIFO is emptied to the trigger level: FIFOTrgLvl[7:4]. If the RxTrgInv bit is low (default state), the ISR[3] interrupt
is generated when the RxFIFO fill level that starts from a level below FIFOTrgLvl[7:4] is filled up to the trigger level
programmed into FIFOTrgLvl[7:4].
Bit 1: FIFORst
Set the FIFORst bit high to clear both the receive and transmit FIFOs of all data contents. After the FIFO reset, the
FIFORst bit must then be set back to 0 to continue normal operation.
Bit 0: RST
Set the RST bit high to reset the MAX3107. The SPI/I2C bus stays active during this reset, therefore, communication
with the MAX3107 is possible. All register bits are reset to their reset state and all FIFOs are cleared.
Once set high, the RST bit must be cleared by writing a 0 to RST.
MODE2 Register
ADDRESS:
0x0A
MODE:
R/W
BIT
7
6
5
4
3
2
1
0
NAME
EchoSuprs
MultiDrop
Loopback
SpecialChr
RxEmtyInv
RxTrigInv
FIFORst
RST
RESET
0
32
Maxim Integrated
MAX3107
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3108EWA+T | IC UART |
| MAX3109ETJ+ | SEMICONDUCTOR OTHER |
| MAX310CPE | IC VIDEO MULTIPLEXER 8X1 16DIP |
| MAX3110EENI+G36 | IC UART SPI COMPAT 28-DIP |
| MAX3120CUA+ | IC TXRX INFRARED IRDA 8-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3107EAG+ | 功能描述:UART 接口集成电路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3107EAG+T | 功能描述:UART 接口集成电路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3107ETG/V+ | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3107ETG/V+T | 功能描述:UART 接口集成电路 SPI/IC UART with 128-Word FIFOs and Internal Oscillator RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3107ETG+ | 功能描述:UART 接口集成电路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。