- 您现在的位置：买卖IC网 > PDF目录9404 > MAX5418LETA+T (Maxim Integrated Products)IC POT DGTL 256-TAP I2C 8-TDFN PDF资料下载
参数资料
| 型号： | MAX5418LETA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/14页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 256-TAP I2C 8-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 接片： | 256 |
| 电阻（欧姆）： | 100k |
| 电路数： | 1 |
| 温度系数： | 标准值 35 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（3x3） |
| 包装： | 标准包装 |
| 产品目录页面： | 1399 (CN2011-ZH PDF) |
| 其它名称： | MAX5418LETA+TDKR |
MAX5417/MAX5418/MAX5419
256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
_______________________________________________________________________________________
9
Analog Circuitry
The MAX5417/MAX5418/MAX5419 consist of a resistor
array with 255 resistive elements; 256 tap points are
accessible to the wiper, W, along the resistor string
between H and L. The wiper tap point is selected by
programming the potentiometer through the 2-wire (I2C)
interface. Eight data bits, an address byte, and a con-
trol byte program the wiper position. The H and L termi-
nals of the MAX5417/MAX5418/MAX5419 are similar to
the two end terminals of a mechanical potentiometer.
The MAX5417/MAX5418/MAX5419 feature power-on
reset circuitry that loads the wiper position from non-
volatile memory at power-up.
Digital Interface
The MAX5417/MAX5418/MAX5419 feature an internal,
nonvolatile EEPROM that stores the wiper state for ini-
tialization during power-up. The shift register decodes
the control and address bits, routing the data to the
proper memory registers. Data can be written to a
volatile memory register, immediately updating the
wiper position, or data can be written to a nonvolatile
register for storage.
The volatile register retains data as long as the device
is powered. Once power is removed, the volatile regis-
ter is cleared. The nonvolatile register retains data even
after power is removed. Upon power-up, the power-on
reset circuitry controls the transfer of data from the non-
volatile register to the volatile register.
Serial Addressing
The MAX5417/MAX5418/MAX5419 operate as a slave
that receives data through an I2C- and SMBus-com-
patible 2-wire interface. The interface uses a serial data
access (SDA) line and a serial clock line (SCL) to
achieve communication between master(s) and
slave(s). A master, typically a microcontroller, initiates
all data transfers to the MAX5417/MAX5418/MAX5419,
and generates the SCL clock that synchronizes the
data transfer (Figure 1).
The MAX5417/MAX5418/MAX5419 SDA line operates
as both an input and an open-drain output. A pullup
resistor, typically 4.7k
, is required on the SDA bus.
The MAX5417/MAX5418/MAX5419 SCL operates only
as an input. A pullup resistor, typically 4.7k
, is
required on the SCL bus if there are multiple masters
on the 2-wire interface, or if the master in a single-mas-
ter system has an open-drain SCL output.
Each transmission consists of a START (S) condition
(Figure 3) sent by a master, followed by the
MAX5417/MAX5418/MAX5419 7-bit slave address plus
the 8th bit (Figure 4), 1 command byte (Figure 7) and 1
data byte, and finally a STOP (P) condition (Figure 3).
Start and Stop Conditions
Both SCL and SDA remain high when the interface is
not busy. A master signals the beginning of a transmis-
sion with a START condition by transitioning SDA from
high to low while SCL is high. When the master has fin-
ished communicating with the slave, it issues a STOP
condition by transitioning the SDA from low to high
while SCL is high. The bus is then free for another
transmission (Figure 3).
Bit Transfer
One data bit is transferred during each clock pulse.
The data on the SDA line must remain stable while SCL
is high (Figure 5).
SDA
START
CONDITION
SCL
S
STOP
CONDITION
P
Figure 3. Start and Stop Conditions
SDA
SCL
*See the Ordering Information/Selector Guide section for other address options.
01
A0
MSB
LSB
NOP/W
ACK
0
1
0*
Figure 4. Slave Address
SMBus is a trademark of Intel Corporation.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27466T23A35S | CONN RCPT 100POS WALL MNT W/SCKT |
| MS27466E23A35S | CONN RCPT 100POS WALL MNT W/SCKT |
| MS27474E8A98PA | CONN RCPT 3POS JAM NUT W/PINS |
| DS1670E+ | IC CTRLR SYSTEM PORTABLE 20TSSOP |
| DS12C887+ | IC RTC W/RAM 128 BYTE 24-EDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5418META | 制造商:Maxim Integrated Products 功能描述:MAXIM MAX5418META, DIGITAL POTENTIOMETERS - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:Maxim MAX5418META, 100Kohm Digital Potentiometer 256-Tap 2.7V-5.25V 8-pin TDFN |
| MAX5418META+ | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 256POS 100KOHM SGL 8TDFN EP - Rail/Tube |
| MAX5418META+T | 功能描述:数字电位计 IC 256-Tap Nonvolatile I2C-Interface RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5418META-T | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5418NETA | 制造商:Maxim Integrated Products 功能描述:256-TAP NONVOLATILE 2-WIRE INTERF - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。