- 您现在的位置：买卖IC网 > PDF目录2011 > MAX5887EGK+D (Maxim Integrated Products)IC DAC 14BIT 3.3V 500MSPS 68-QFN PDF资料下载
参数资料
| 型号： | MAX5887EGK+D |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/18页 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 3.3V 500MSPS 68-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 30 |
| 设置时间： | 11ns |
| 位数： | 14 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 130mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 68-VFQFN 裸露焊盘 |
| 供应商设备封装： | 68-QFN 裸露焊盘（10x10） |
| 包装： | 管件 |
| 输出数目和类型： | 2 电流，单极 |
| 采样率（每秒）： | 500M |
MAX5887
3.3V, 14-Bit, 500Msps High Dynamic
Performance DAC with Differential LVDS Inputs
14
______________________________________________________________________________________
The noise density requirements (Table 2) for a
GSM/EDGE-based system can again be derived from
the system’s Tx mask. With a worst-case noise level of
-80dBc at frequency offsets of
≥6MHz and a measure-
ment bandwidth of 100kHz, the minimum noise density
per hertz is calculated as follows:
SNRMIN = -80dBc - 10 log10(100 103Hz)
SNRMIN = -130dBc/Hz
Since random DAC noise adds to both the spurious tones
and to random noise from other circuit elements, it is rec-
ommended reducing the specification limits by about
10dB to allow for these additional noise contributions
while maintaining compliance with the Tx mask values.
Other key factors in selecting the appropriate DAC for
the Tx path of a multicarrier GSM/EDGE system is the
converter’s ability to offer superior IMD and MTPR perfor-
mance. Multiple carriers in a designated band generate
unwanted intermodulation distortion between the individ-
ual carrier frequencies. A multitone test vector usually
consists of several equally spaced carriers, usually four,
with identical amplitudes. Each of these carriers is rep-
resentative of a channel within the defined bandwidth of
interest. To verify MTPR, one or more tones are
removed such that the intermodulation distortion perfor-
mance of the DAC can be evaluated. Nonlinearities
associated with the DAC create spurious tones, some
of which may fall back into the area of the removed
tone, limiting a channel’s carrier-to-noise ratio. Other
spurious components falling outside the band of inter-
est can also be important, depending on the system’s
spectral mask and filtering requirements. Going back to
the GSM/EDGE Tx mask, the IMD specification for adja-
cent carriers varies somewhat among the different GSM
standards. For the PCS1800 and GSM850 standards,
the DAC must meet an average IMD of -70dBc.
Table 3 summarizes the dynamic performance require-
ments for the entire Tx signal chain in a four-carrier
GSM/EDGE-based system and compares the previous-
ly established converter requirements with a new-gen-
eration high dynamic performance DAC.
The four-tone MTPR plot in Figure 12 demonstrates the
MAX5887’s excellent dynamic performance. The center
frequency (fCENTER = 32MHz) has been removed to
allow detection and analysis of intermodulation or spuri-
ous components falling back into this empty spot from
adjacent channels. The four carriers are observed over
a 12MHz bandwidth and are equally spaced at 1MHz.
Each individual output amplitude is backed off to -12dB
FS. Under these conditions, the DAC yields an MTPR
performance of -78dBc.
Grounding, Bypassing, and Power-Supply
Considerations
Grounding and power-supply decoupling can strongly
influence the performance of the MAX5887. Unwanted
digital crosstalk may couple through the input, refer-
ence, power supply, and ground connections, affecting
dynamic performance. Proper grounding and power-
supply decoupling guidelines for high-speed, high-fre-
NUMBER OF
CARRIERS
CARRIER
POWER LEVEL
(dB FS)
DAC NOISE DENSITY
REQUIREMENT
(dB FS/Hz)
2
-6
-146
4
-12
-152
8
-18
-158
Table 2. GSM/EDGE Noise Requirements
for Multicarrier Systems
SPECIFICATION
SYSTEM TRANSMITTER
OUTPUT LEVELS
DAC REQUIREMENTS WITH
MARGINS
MAX5887 SPECIFICATIONS
SFDR
80dBc
86dBc
89dBc*
Noise Spectral Density
-130dBc/Hz
-152dB FS/Hz
-157dB FS/Hz
IMD
-70dBc
-75dBc
-85dBc
Carrier Amplitude
N/S
-12dB FS
Table 3. Summary of Important AC Performance Parameters for Multicarrier GSM/EDGE
Systems
*Measured within a 15MHz window.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5888EGK+D | IC DAC 16BIT 3.3V 500MSPS 68-QFN |
| MAX5889EGK+D | IC DAC 12BIT LVDS 600MSPS 68-QFN |
| MAX5890EGK+D | IC DAC 14BIT LVDS 600MSPS 68-QFN |
| MAX5891EGK+D | IC DAC 16BIT LVDS 600MSPS 68-QFN |
| MAX5893EGK+D | IC DAC 12BIT DUAL 500MSPS 68-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5887EGK-TD | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5887EVKIT | 功能描述:数模转换器- DAC Evaluation Kit for the MAX5886 MAX5887 MAX5888 RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5888AEGK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX5888AEGK+D | 功能描述:数模转换器- DAC 16-Bit 500Msps DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5888AEGK+TD | 功能描述:数模转换器- DAC 16-Bit 500Msps DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。