- 您现在的位置：买卖IC网 > Datasheet目录43 > MAX5930AEEG+ (Maxim Integrated)IC HOT SWAP CTLR PWR SEQ 24QSOP Datasheet资料下载
参数资料
| 型号： | MAX5930AEEG+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 19/23页 |
| 文件大小： | 331K |
| 描述： | IC HOT SWAP CTLR PWR SEQ 24QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 1 V ~ 15 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 管件 |
With a 22nF gate capacitor, the inrush current, charge,
and discharge times are:
Case B: Fast Turn-On (With Current Limit)
In applications where the board capacitance (C
BOARD
)
is high, the inrush current causes a voltage drop across
R
SENSE
that exceeds the startup fast-comparator
threshold. The fast comparator regulates the voltage
across the sense resistor to V
FC,TH
. This effectively reg-
ulates the inrush current during startup. In this case,
the current charging C
BOARD
can be considered con-
stant and the turn-on time is:
The maximum inrush current in this case is:
Figure 6 shows the waveforms and timing diagrams for
a startup transient with current regulation (see the
Typical Operating Characteristics section). When oper-
ating under this condition, an external gate capaci-
tor is not required.
ON Comparators
The ON comparators control the on/off function of the
MAX5930A/MAX5931A/MAX5931B. ON_ is also used to
reset the fault latch (latch mode). Pull V
ON_
low for
100祍, t
UNLATCH
, to reset the shutdown latch. ON_ also
programs the UVLO threshold (see Figure 10). A resis-
tive divider between V
IN_
, V
ON_
, and GND sets the
user-programmable turn-on voltage. In power-sequenc-
ing mode, an RC circuit can be used at ON_ to set the
delay timing (see Figure 11).
Using the MAX5930A/MAX5931A/
MAX5931B on the Backplane
Using the MAX5930A/MAX5931A/MAX5931B on the
backplane allows multiple cards with different input
capacitance to be inserted into the same slot even if
the card does not have on-board hot-swap protection.
The startup period can be triggered if IN_ is connected
to ON_ through a trace on the card (Figure 12).
Input Transients
The voltage at IN1, IN2, or IN3 must be above V
UVLO
dur-
ing inrush and fault conditions. When a short-circuit con-
dition occurs on the board, the fast-comparator trips
cause the external MOSFET gates to be discharged at
50mA according to the mode of operation (see the Mode
section). The main system power supply must be able to
sustain a temporary fault current, without dropping below
the UVLO threshold of 2.45V, until the external MOSFET is
completely off. If the main system power supply collapses
below UVLO, the MAX5930A/MAX5931A/MAX5931B
force the device to restart once the supply has recov-
ered. The MOSFET is turned off in a very short time result-
ing in a high di/dt. The backplane delivering the power to
the external card must have low inductance to minimize
voltage transients caused by this high di/dt.
I
V
R
INRUSH
FCTH
SENSE
=
,
t
C
V
R
V
ON
BOARD
IN
SENSE
FCTH
=
?/DIV>
?/DIV>
I
F
pF
nF
A
mA
t
nF
V
nC
A
ms
t
nF
V
nC
mA
ms
nF
V
nC
s
INRUSH
CHARGE
DISCHARGE NORMAL
DISCHARGE STRONG
=
?/DIV>
+
?/DIV>
+ =
=
?/DIV>
+
?/DIV>
=
=
?/DIV>
+
=
=
?/DIV>
+
=
6
600
22
100
0 26 5
22
10 4
60
100
2 89
22
10 4
60
3
0 096
22
10 4
60
5 8
.
.
.
.
.
.
.
(
)
(
)
?/DIV>
?/DIV>
Low-Voltage, Triple, Hot-Swap Controllers/
Power Sequencers/Voltage Trackers
______________________________________________________________________________________ 19
Figure 10. Adjustable Undervoltage Lockout
GATE_
SENSE_
V
TURN-ON
-
(R
2
x R
1
) V
ON
,
TH
R
2
ON_
V
IN
IN_
R
1
R
2
MAX5930A
MAX5931A
MAX5931B
Figure 9. Operating with an External Gate Capacitor
GATE_
SENSE_
GND
ON_
R
SENSE_
V
OUT_
C
GATE
C
BOARD
V
IN_
IN_
R
PULLUP
STAT_
MAX5930A
MAX5931A
MAX5931B
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5932ESA+T | IC HOT-SWAP CONTROLLER 8-SOIC |
| MAX5933EESA+ | IC HOT-SWAP CONTROLLER 8-SOIC |
| MAX5934EEE+ | IC HOT-SWAP CONTROLLER 16-QSOP |
| MAX5935EAX+ | IC CTRLR POWER QUAD 36-SSOP |
| MAX5937LCESA+ | IC HOT-SWAP CTRLR -48V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5930AEEG+ | 功能描述:热插拔功率分布 Triple Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5930AEEG+T | 功能描述:热插拔功率分布 Triple Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5930EEG | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5930EEG+ | 功能描述:热插拔功率分布 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5930EEG+T | 功能描述:热插拔功率分布 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。