- 您现在的位置：买卖IC网 > PDF目录19751 > MAX5965AUAX+T (Maxim Integrated)IC PSE CTRLR FOR POE 36SSOP PDF资料下载
参数资料
| 型号： | MAX5965AUAX+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 19/54页 |
| 文件大小： | 1334K |
| 描述： | IC PSE CTRLR FOR POE 36SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 类型： | 以太网供电控制器（PoE） |
| 应用： | IP 电话，LAN 网络供电，网络路由器和交换机 |
| 内部开关： | 无 |
| 电源电压： | 2.4 V ~ 3.6 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-BSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
High-Power, Quad, Monolithic, PSE Controllers
for Power over Ethernet
______________________________________________________________________________________ 19
Powered Device Classification
(PD Classification)
During the PD classification mode, the MAX5965A/
MAX5965B force a probe voltage (-18V) at DET_ and
measure the current into DET_. The measured current
determines the class of the PD.
After each classification cycle, the device sets the
CL_END_ bit (R04h/05h[7:4]) high and reports the clas-
sification results in the status registers R0Ch[6:4],
R0Dh[6:4], R0Eh[6:4], and R0Fh[6:4]. The CL_END_ bit
is reset to low when read through register R05h or after
a port reset. Both events registers, R04h, and R05h are
cleared after the port powers down. Table 2 shows the
IEEE 802.3af requirement for a PSE classifying a PD at
the power interface (PI).
The MAX5965A/MAX5965B support high power beyond
the IEEE 802.3af standard by providing additional clas-
sifications (Class 5 and 2-event classification).
Class 5 PD Classification
During classification, if the MAX5965A/MAX5965B
detect currents in excess of I
CLASS
> 48mA, then the
PD will be classified as a Class 5 powered device.
Status registers R0Ch[6:4] or R0Dh[6:4] or R0Eh[6:4] or
R0Fh[6:4] will report the Class 5 classification result.
2-Event (Class 6) PD Classification
When 2-event classification is activated, the classifica-
tion cycle is repeated three times with 8ms wait time
between each cycle (see Figure 1b). Between each
classification cycle, the MAX5965A/MAX5965B do not
reset the port voltage completely but keeps the output
voltage at -9V. The EN_CL6 bits in R1Ch[7:4] enable 2-
event classification on a per port basis.
Powered State
When the MAX5965A/MAX5965B enter a powered
state, the t
START
and t
DISC
timers are reset. Before
turning on the port power, the MAX5965A/MAX5965B
check if any other port is not turning on and if the
t
FAULT
timer is zero. Another check is performed if the
ACD_EN_ bit is set, in this case the OSC_FAIL bit must
be low (oscillator is okay) for the port to be powered.
If these conditions are met, the MAX5965A/MAX5965B
enter startup where it turns on power to the port. An
internal signal, POK_, asserts high when V
OUT_
is within
2V from V
EE
. PGOOD_ status bits are set high if POK_
stays high longer than t
PGOOD
. PGOOD_ immediately
resets when POK_ goes low (see Figure 2).
The PG_CHG_ bit sets when a port powers up or down.
PWR_EN_ sets when a port powers up and resets when
a port shuts down. The port shutdown timer lasts 0.5ms
and prevents other ports from turning off during that peri-
od, except in the case of emergency shutdowns (RESET
= L, RESET_IC = H, V
EEUVLO,
V
DDUVLO,
and T
SHD
).
The MAX5965A/MAX5965B always check the status of
all ports before turning off. A priority logic system deter-
mines the order to prevent the simultaneous turn-on or
turn-off of the ports. The port with the lesser ordinal
number gets priority over the others (i.e., port 1 turns on
first, port 2 second, port 3 third, and port 4 fourth).
Setting PWR_OFF_ high turns off power to the corre-
sponding port.
Table 2. PSE Classification of a PD (Refer to Table 33-4 of the IEEE 802.3af)
MEASURED I
CLASS
(mA)
CLASSIFICATION
0 to 5
Class 0
> 5 and < 8
May be Class 0 and 1
8 to 13
Class 1
> 13 and < 16
May be Class 1 or 2
16 to 21
Class 2
> 21 and < 25
May be Class 2 or 3
25 to 31
Class 3
> 31 and < 35
May be Class 3 or 4
35 to 45
Class 4
> 45 and < 51
May be Class 4 or 5
51 to 68
Class 5
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2214-SWBML TR | IC REG LDO 3.3V/1.6V 10MLF |
| MAX5929CEEG+T | IC HOT SWAP CTLR QUAD 24QSOP |
| GBM03DRKN | CONN EDGECARD 6POS DIP .156 SLD |
| VE-B6M-CY-B1 | CONVERTER MOD DC/DC 10V 50W |
| MAX5929DEEG+T | IC HOT SWAP CTLR QUAD 24QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5965BCAX+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5965BCAX+T | 制造商:Maxim Integrated Products 功能描述:HIGH-POWER, QUAD, MONOLITHIC, PSE CONTROLLERS FOR POWER OVER - Tape and Reel |
| MAX5965BEAX+ | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5965BEAX+T | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5965BUAX+ | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。